7. In practical terms, explain how a LOW p-value connote SIGNIFICANCE (Recall that thesmaller the p-value is, the more significant the factor becomes)?8.What is the significance of Coefficient of Determination, R29. When the test for normality fails, what are the things to resort to?10.What advantages, if any, are there in the use of a 3k full factorial designs over the 2kdesigns?11. In selecting an appropriate fractional factorial design, what considerations should betaken to guard the validity of the results?12. When the following test statistics yield a LOW value, what does this mean?(a) R2 (b) Lack of Fit (p-value),(c) Desirability Index

Answered: 7. In practical terms, explain how a…

7. In practical terms, explain how a LOW p-value connote SIGNIFICANCE (Recall that the smaller the p-value is, the more significant the factor becomes)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 3: Insulation To=1 Toowwww Steam Tx2 T₂ T3 www www R₁ R₁ R₂ www.T R₂ Steam at T1 = 320 °C flows in a cast iron pipe (k= 80 W/m. °C) whose inner and outer diameters are 5 cm = 0.05 m and D₂ = 5.5 cm = 0.055 m, respectively. The pipe is covered with 3-cm-thick glass wool insulation with k = 0.05 W/m. °C. Heat is lost to surroundings at T2 = 5 °C by natural convection and radiation, with a combined heat transfer coefficient of h₂ = 18 W/m². °C. Taking the heat transfer coefficient inside the pipe to be h₁ = 60 W/m². °C, determine the temperature drops across the pipe and the insulation. The determination is based on a unit length of the pipe (L = 1 m). Assumptions 1. Heat transfer is one-dimensional since there is no indication of any change with time. 2. Heat transfer is one-dimensional since there is thermal symmetry about the centreline and no variation in the axial direction. 3. Thermal conductivities are constant. 4. The thermal contact resistant at the interface is…
Chapter 3: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is called a 15. The feature symbol specifies that a group of two or more interrupted features of size are to be considered one single feature of size. 16. For an individual regular feature of size, no element of the feature shall extend beyond the maximum material condition boundary (envelope) of perfect form. This statement is the essence of 17. What is the name of the symbol used to identify physical features of a part as a datum feature and must not be applied to centerlines, center planes, or axes? 18. The is the condition in which a feature of size contains the maximum amount of material within the stated limits of size. 19. The total positional tolerance equals the sum of the tolerance and the tolerance.
Read each statement carefully and answer by True or False (if False then, correct the statement). 1- Process control combines how physics, chemistry, and biology work in operating equipment and an understanding of dynamic systems. 2- When a second letter is used in instrumentation symbols, e.g., Pressure Indicator Controller (PIC), it defines the measured or initiating variables. 3- P&ID contains the sensor details such as physical principle and measurement range. 4- FRC 82516: Flow Recording Controller, area no 825, process unit 8, loop number 16. 5- P&ID excludes equipment identification.
13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is called a 15. The feature symbol specifies that a group of two or more interrupted features of size are to be considered one single feature of size. 16. For an individual regular feature of size, no element of the feature shall extend beyond the maximum material condition boundary (envelope) of perfect form. This statement is the essence of 17. What is the name of the symbol used to identify physical features of a part as a datum feature and must not be applied to centerlines, center planes, or axes? 18. The is the condition in which a feature of size contains the maximum amount of material within the stated limits of size. 19. The total positional tolerance equals the sum of the tolerance and the tolerance. 20. Refer to the figure below. Read the feature control frame in the figure and write it out below. Ø 010M ABMCM
PLEASE SHOW COMPLETE FBD AND SOLUTION. PROVIDE AN EXPLANATION FOR EACH PROCEDURE.
Weights measured in grams of randomly selected M&M plain candies: 0.957 0.912 0.925 0.886 0.920 0.958 0.915 0.914 0.947 0.939 0.842 What is the z-score for an M&M that weighs less than 0.866 grams? (round to the tenths place)
Can someone slove the fx and fy equations in the below questions solution in steps to how we got f1 and f2 values. Thanks.
A new electronic component for aircraft is tested to withstand temperatures as low as -50°F. One engineer suggests that the device cannot actually stand temperatures that low. What are the Type I and Type II errors? Type I: The device CAN NOT withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN.Type II: The device CAN withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN NOT. Type I: The device CAN withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN NOT.Type II: The device CAN NOT withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN. Is the answer the first or second bullet point?
Geometric Dimensioning and Tolerancing was designed to insure the proper assembly of Geometric Dimensioning and Tolerancing is a symbolic language used to specify the Plus or minus tolerancing generates a -shaped tolerance zone. Bonus tolerance equals the difference between the actual mating envelope size and the Geometric tolerancing allows the maximum available and, consequently, the most to improve parts. and reduce ,and of features on a part.
Which of the followings are not valid names for identifiers/variables?1. first_name2. 2modules3. switch4. Average Marks5. _test1
Assume the missing data if any
show complete solutionpls write legibly