7. A fire tube boiler develops 75,000 kilograms of steam at a pressure of 12,500 kpa and a temperature of 660°C for a period of 8 hours. The feedwater temperature is maintained at 95°C. If the boiler efficiency is 87.5%, find the average amount of coal burned in lb/min if its heating value is 52,337.5 KJ/kg.

7. A fire tube boiler develops 75,000 kilograms of steam at a pressure of 12,500 kpa and a temperature of 660°C for a period of 8 hours. The feedwater temperature is maintained at 95°C. If the boiler efficiency is 87.5%, find the average amount of coal burned in lb/min if its heating value is 52,337.5 KJ/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2) A 100 Mul thermal plant has an over-all efficiency of 32%. If the coal burned has a heating value of 10,500 BTU/1b Calculate the coal consumption in kg/kw-hr =
d) The condenser of a thermal power plant is to be cooled by a nearby river at 14.5°C, allowing a temperature gradient of 11.5°C for effective heat transfer, stating your reasons, calculate the minimum condenser pressure in bar.
I need correct answer in 20 minutes please Find the cycle efficiency and specific steam consumption of a reheat cycle (Fig. 2.7a) operating between pressures of 3 MPa and 0.004 MPa, with superheat temp of 450 °C. Assume that the first expansion is carried out to the point where the steam is dry saturated and then the steam is reheated to the original superheat temp. The feed pump term may be neglected Boiler Reheater a High-P turbine. P = Ps= Preheal Pump Condenser Low-P turbine Figure (2.7 a) High-pressure turbine Reheating Low-pressure turbine
3. A water-tube boiler having a heating surface of 325.23 m² evaporates 6349.21 kg of water in an hour from a feed temperature of 66 °C. Boiler pressure is at 1.04 MPaa and the steam quality at the boiler outlet is 99 %. What percent of its rated Bo. Hp was the boiler developing?
Refrigerant 134a is used in a cooling system operating according to the ideal cooling cycle with vapor compression for cooling the cold storage in the milk processing plant. The flow rate of the refrigerant is 0.10 kg/s. The condenser and evaporator pressures are 1000 kPa and 600 kPa, respectively. a) Calculate the cooling capacity as (kW). b) Calculate the volumetric flow rate of the refrigerant at the compressor inlet. c) Calculate the efficiency coefficient of the cooling system.
A refrigerant 134a of a vapor compression refrigeration system includes a liquid-suction heat exchanger. The heat exchanger cools saturated liquid coming from the condenser from 45 °C to 37 °C with the saturated vapor which comes from the evaporator at -8 °C. Calculate: a.) The COP of the system without heat exchanger. b.) The COP of the system with the heat exchanger. c.) Find the percent increase of performance of the system with the heat exchanger based on the system without heat exchanger. d.) Draw the schematic and P-h diagram of the two set-up.
A certain power plant produces a net power output of 120 MW. The constant pressure condenser operates at 8 kPa and the constant pressure boiler operates at 1 MPa. The steam enters the turbine, which operates at 88% efficiency at 600°C, and the water leaving the condenser at 8kPa enters the 72% efficient pump. Find: a) mass flow rate in kg/hr of the working fluid, b) heat suplied to the boiler in kJ/hr, c) heat rejected to the condenser in kJ/hr; I want a personalized answer so please do not copy from other's work. I need it ASAP
12- Water vapor at 20000kg /hour flows into a steam boiler with a specific volume of 225 kPa 0.7565 m ^ 3 / kg. Calculate the time required to increase 1 ton of water to 200 ° C in the boiler if the insulation of the boiler is bad and loses heat to the environment of 100 kW with the energy it takes from the fuel in the combustion chamber. A.) 2061sB.) 1117sC.) 7643 sD.) 965 sE.) 8973 s
Q.2: A refrigeration system using refrigerant 22 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature 42°C. -8°C and the condensing temperature (a) Determine the volume flow of refrigerant measured in cubic is meters inlet at the to the compressor. second per (b) Calculate the power required by the compressor. (c) At the entrance to the evaporator what is the fraction of vapor in the mixture.
A power plant was analysed based on Carnot cycle, the evaporator supplie 442 kJ of heat per cycle at 512°C and condenser cooling fluid was maintained at 36°C. (a).Determine the amount of heat rejected in the condenser? Provide answer to no decimal place and insert the unit symbol in kilo.... 1 °C is 273K in this question if required.
Pls. Answer thank you! A cooling tower has an efficiency of 65%. Water enters the tower at 55°C. The wet bulb temperature of surrounding air is 27°C. What is the temperature of water leaving the tower?
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side