6-40. The compound beam is fixed supported at C and supported by rockers at A and B. If there are hinges (pins) at D and E, determine the components of reaction at the supports. Neglect the thickness of the beam. 900 lb 400 lb 2 ft 300 lb B inf -6 ft4 ft4 ft DY A 4 ft 2 ft Prob. 6-40 E S 650 lb 13/12 2 ft -8 ft- C

6-40. The compound beam is fixed supported at C and supported by rockers at A and B. If there are hinges (pins) at D and E, determine the components of reaction at the supports. Neglect the thickness of the beam. 900 lb 400 lb 2 ft 300 lb B inf -6 ft4 ft4 ft DY A 4 ft 2 ft Prob. 6-40 E S 650 lb 13/12 2 ft -8 ft- C

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter6: Beam–columns

Section: Chapter Questions

Problem 6.6.2P

See similar textbooks

Similar questions

II A. USE THE PORTAL METHOD AND DETERMINE (APPROXI MAITE) THE REACTIONS @SUPPORTS A, B, C ANDO. B. USE THE CANTILEVER METHOD AND DETERMINE A,B,C AND D. ALL COLUMNS HAVE THE J 1 2 FF F 5m OVEN I IZKUE Im THE REACTIONS SAME CROSS-SECTIONAL AREA. 5m H 4m 4m D 70707 .: De=R-U De-12-329 Di 3n 3(3)-9 · D. De tD D' 9+9=18 AT SUPPORTS
-55./Draw the influence line for the force in member CJ. then compute the maximum live force (tension or compression) that can be developed in this member due to a uniform live load of 3 kN/m which is transmitted to the *6-60. E DE of th force (te- member truss along the bottom cord. transmi
4/39 SS Determine M 5' A L 4' B the forces in members CD, CJ, and DJ. -6 panels at 3'- L K L с J D L I H E L F L L G
*2-16. Classify each of the structures as statically determinate, statically indeterminate, or unstable. If indeterminate, specify the degree of indeterminacy. The supports or connections are to be assumed as stated. roller pin fixed 8 bns Aanogque od tneno (a) A roller В Гoller rollerC (b) ol d no no A D pin roller B rollerC pin (c) Prob. 2-16
MECH 1 ASSIGNMENT - 2M 20 k G y 10k E Problem A truss is subjected to the following forces as shown. Determine: (a.) The magnitude of the resultant of the external forces, R (kips). *Kip (k)-a unit of force, equivalent to 1000 lbs. (Av. AH. Bv) 1 [10] 15 25 25 10 ft ft ft ft ft In short, solve for the reactions at the supports using the equilibrium equations EFv, ΣFH, ΣΜ (AH, Av, Bv) C 20 k 20 k F 10 k 15 ft 15 ft 10 ft 25 ft B' X
Q/ Replace the force system acting on the beam with an equivalent resultant force and moment at B? * 650 N 500 N 30° 300 N 1500 N m B -3 m- 5 m- -2 m- 1 Add file
De term ine the kin d and am ount of stress in e ach mem ber of the truss shown by the method of jo in ts in figure P 5-2 (page 76).- 1000lb 1000lb 1000lb 1000Ib 1000 Ib U. h = 20 ft 500lb 500 Ib L. L. RAV 6 pane ls at 10' - 6 ft RBy Note: 1. F o llo w strictly the lecture notes g iv en. Draw the FBD of e ach jo in t 2. Sum m a rize and tabu la te your answers. 3. Compu te the bar forces up to member U,L3 on ly because the truss lo a d in g is sym metric aland the bar forces of right sid e members are id en tic al w ith th e left s ide members. But you in c lu de th e rig ht sid e mem bers in have to the tabu la tion. 4. Show the com puta tio n ho w the leng th s were obta in ed. 5. Look for your own data in the table provided. 6. Copy the problem , data of problem and fig ure of the proble m TABULAT ION FOR SUMMAR Y OF COMPUTATION OF BAR FORCES METHOD OF JOINTS (PROBLEM P5-2 PAGE 76) Mem ber Identification Length Bar Forc e Туре of ft Ib force LOL1 10 3750 Tensio n L1L 2 10 Tension…
The frame shown in figure below is hinged to rigid supports at A and E. Find the components of the hinge forces at A and E and the forces in members BC and BD. 120 RẠH B TRAV REH E -3- ReV
Dr. A H.W.5: A rigid bar ABCD is supported by two bars, as shown in Fig- ure 3 .There is no strain in the vertical bars before load Pis applied. After load P is applied, the normal strain in rod (1) is -570 pm/m. Determine (b) the normal strain in rod (2) if there is a l-mm gap in the connection at pin C before the load is applied. (c) the normal strain in rod (2) if there is a l-mm gap in the connection at pin B before the load is applied. (a) the normal strain in rod (2). (2) 1,500 mm 360 mm 140 mm 240 mm Rigid bar bber C B 900 mm (1)
|%A• In. ? Asst. Prof. Muhammed Abbas المعلم منذ ۱۲ ساعات مضت. H.W.2: Find the 40 k force in each G member of the 5 k truss. 16 ft V17 F 10 k 10 k 16 ft 3 B - 8 ft- 8 ft- 4 ft 4 ft 4 ft 4 ft 4.
Draw the SFD and BMD for the following frame. 120 KN 30 kN/m 60 KN 8 m A >>> 3 m 1 m B 6 m
The homogeneous wire ABCD is bent as shown and is attached to a hinge at C. The length BCindicated by b is 94 mm. Determine the length L for which portion BDC of the wire is horizontal. L В IC 60 mm A The length L for which portion BCD of the wire is horizontal is mm.