5. You are working in an engineering workshop. Towards the end of your shift, you observe another worker disposing of old machine oil directly into the gutter in the street. This method of disposal is incorrect as the used machine oil A. should not be emptied into the gutter until it rains. B. should have been poured directly into a drain instead. C. is an environmental hazard and should be stored in a waste container. D. must first have water added to it, then it can be poured into the gutter. 6. In most workplaces, employees must wear PPE. What does PPE stand for? A. proactive personal equipment B. personal protective equipment C. protective plasticised equipment D. proper protective equipment

5. You are working in an engineering workshop. Towards the end of your shift, you observe another worker disposing of old machine oil directly into the gutter in the street. This method of disposal is incorrect as the used machine oil A. should not be emptied into the gutter until it rains. B. should have been poured directly into a drain instead. C. is an environmental hazard and should be stored in a waste container. D. must first have water added to it, then it can be poured into the gutter. 6. In most workplaces, employees must wear PPE. What does PPE stand for? A. proactive personal equipment B. personal protective equipment C. protective plasticised equipment D. proper protective equipment

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. When the pressure of the evaporator chamber is decreased, the boiling point of the solutions inside the chamber will: 2. It states that for a given concentration, the boiling point of the solution is a linear function of the boiling point of the solvent. a.Boiling point rise b.Enthalpy-concentration chart c.Duhring's rule d.Dalton's law 3.
7. One precaution that needs to be followed in a work area displaying the sign shown above: A. avoid using solvents. B. wear a leather apron. C. wear rubber gloves. D. prohibit welding. 8. A length of copper pipe measures 15.3 m. According to a job's specifications, the pipe needs to be cut into 3.2-m-long pieces. How many 3.2-m-long pieces of pipe can be cut from the original 15.3-m-long copper pipe? A. one B. two C. three D. four 9. You observe a worker emptying used degreaser cleaning fl uid into the sink in a workshop. What should you do? A. Notify your immediate supervisor of the hazard the next day. B. Refer the worker to the company policy manual. C. Advise the worker that it is an occupational health and safety hazard. D. Ignore the situation as there is nothing wrong with this disposal method.
When two fluids differ in densities, which of the following will always occur?A. The denser fluid will always stay at the bottom of the container.B. The denser fluid is heavier in mass if the volume of the liquids is equal.C. The lighter fluid experiences more vapor pressure than the denser fluid.D. The lighter fluid has more tendency to exhibit capillary movement.
EDUKAS NG AMARAN Republic of the Philippines Department of Education REGION VI - WESTERN VISAYAS SCHOOLS DIVISION OF CADIZ CITY CADUHA-AN NATIONAL HIGH SCHOOL BRGY. CADUHA-AN, CADIZ CITY, NEGROS OCCIDENTAL Test II. Put your correct answer in the number correspondence 18 12 19 13 20 14 15 21 16 22 23 17 E.Normal F Oil Depos A. Too Hot B.Worn E.Ash Deposits Mechanical Damage C.Detonation D.Splash Deposit H.Pre Ignition K.Gap Bridging I.High Speed Glazing L.Carbon Deposit H. in Spark Plug insulator lYpes, How many types are they? В.5 С.3 D.4
(b) Bathroom sinks and some other fixtures include an overflow opening in the basin. This opening is located on the wall and near the top of the basin. The overflow opening serves two important functions: If the water tap is left on while the drain stopper is closed, the opening will channel water down into the drain opening rather than letting is spill out of the sink onto the floor. The overflow allows the sink to drain faster by introducing air into the system. A sink with a dimension given in Figure Q2(b), has water flows into it at a rate of 8 L/min. If the drain stopper is closed and water level in the sink remains constant, determine the average velocity of water flows through the 3.0 cm diameter overflow hole. Front 3 cm diameter overflow holes Q-8 L/min 15 3/4| 40 cm 15 cm Side (a) Figure Q2: (a) Picture of the sink; (b) Sink dimension (Ь)
Project 2: In company that designs road cars and heavy trucks, it important to make the proper selection of the engines. Your part as a system energy engineer is to make a proper selection between an engine operates on Otto cycle/gasoline engine or Diesel cycle/diesel engine. Your head of department asked you to provide a detailed technical report that shows your selection for engine to be used with heavy truck vehicle. This is best achieved by performing the following tasks: Section.1: 1. Which engine does operate at lower ??? and has higher air-fuel mass ratio? 2. Which engine does burn fuel more completely? 3. Which engine has lower fuel cost? 4. Explain what compression ratio for Otto and Diesel cycles means 5. Explain what cut-off ratio for Diesel cycles means 6. Explain the limitations of SI engines in terms of their ability to operate at much higher compression ratios. What is this limitation called? 7. Provide general plot(s) for thermal efficiency, ? vs compression ratio, r…
Q2) briefly explain using appropriate sketches three methods used for removing moisture from compressed air. (air driers)
FLAKABLE LIQUID 3. One precaution that needs to be foliowed in a work area displaying the sign shown above is wear a leather apron. b. avoid using solvents. C. wear rubber gloves. d. prohibit welding. a.
SG of Water=1.0 SG of Mercury=13.6 SG of n-Octane=0.65
He enjoys a bath in the evening نقطة واحدة have having to have
Two techs are discussing oil coolers. Technician A says that when inspecting oil- to-water type coolers, look for mixing of the fluids: oil in the coolant, and coolant in the oil. Technician B says that when inspecting oil-to-air type coolers, look for oil in the coolant only. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor B
How much should you charge to wash alI the windows in Seattle?