5. A vertical sheet pile supports a horizontal backfill having a height of 4.5 m. The backfill has unit weight of 19.67 kN/m² a an angle of fiction of 35 degree. Compute the required depth "d" of the penetration (ΣM bottom = 0) Compute the total active force on the sheet file a) b) c) Compute the maximum bending moment in the cantilever pile 4.5 m d 19.67 kN/m³ d=3.25 m Pa 159.06 kN/m Mmax 151.6 kNm 19.67 kN/m³

5. A vertical sheet pile supports a horizontal backfill having a height of 4.5 m. The backfill has unit weight of 19.67 kN/m² a an angle of fiction of 35 degree. Compute the required depth "d" of the penetration (ΣM bottom = 0) Compute the total active force on the sheet file a) b) c) Compute the maximum bending moment in the cantilever pile 4.5 m d 19.67 kN/m³ d=3.25 m Pa 159.06 kN/m Mmax 151.6 kNm 19.67 kN/m³

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.1P

See similar textbooks

Similar questions

An anchored sheet pile wall supports a mass of soil 7.3m high with a horizontal surface. The angle of friction of the soil is 31o with a unit weight of 1.96 g/cm^3. The total height of the sheet pile is 10.5m which is supported by an anchor bolt placed 1.2m below the ground surface which has a spacing of 3m center-to-center. (a) Compute the active force(b) Compute the fraction of the theoretical maximum passive resistance of the total embedded length which must be mobilized for equilibrium.(c) Compute the tension in the anchor bolt.
A vertical sheet piled wall is shown in Fig. below, the properties of the soil both behind and front of the wall are y = 21 kN/m³, $ = 30°, C = 0. ont of Determine the min. penetration depth of pile to achieve: and force T A N.G.L M 1.2m D T 6m BUNUN a. Free earth support. d L C B
A vertical sheet pile supports a horizontal backfill having a height of 4.5m. The backfill has a unit weight (γsat) of 19.67 kN/m^3 and an angle of internal friction of 35o. (1) Compute the required depth of penetration, (2) compute the total active force on the sheet pile, (3) compute the maximum bending moment in the cantilever sheet pile.
A cantilever sheet pile wall supports a horizontal backfill having a unit weight of 16 kN/m^3, angle of internal friction is 30°. The backfill is 4m high.a. Compute the depth of embedment required for stability of the sheet pile using factored moment method with a factor of safety on the passive resistance equal to 2.b. Compute the total active force on the sheet pile.c. Compute the total passive force on the sheet pile.
A Flownet has been drawn as shown in the figure. Point A and C are at elevation h, and he respectively above the datum. Given: H=4m h₁ = 4.7m h₂ = 1.4m Determine the: @Compute the piezometric pressure at point A in kPa. compute the piezometric pressure at point C in kPa. Compute the piezometric head at point B in meters. 12 m h₁ Sheer Pile h₂ H 36m
For the braced cut described in Problem 15.16, assume that all = 170 MN/m2. a. Determine the sheet pile section (section modulus) b. What is the section modulus of the wales at level A? 15.16 Refer to the braced cut in Figure 15.50, for which = 17 kN/m3, = 30, and c = 0. The struts are located at 3 m on center in the plan. Draw the earth pressure envelope and determine the strut loads at levels A, B, and C. FIG. 15.50
A 5 m wide braced excavation is made in a saturated clay, as shown in Figure P19.1, with the following properties: c = 20 kN/m2, = 0, and = 18.5 kN/m3. The struts are spaced at 5 m center to center in plan. a. Determine the strut forces. b. Determine the section modulus of the sheet pile required, assuming all = 170 MN/m2. c. Determine the maximum moment for the wales at levels B and C.
The cross section of a braced cut supporting a sheet pile installation in a clay soil is shown in Figure 14.22. Given: H = 12 m, clay = 17.9 kN/m3, = 0, c = 75 kN/m2, and the center-to-center spacing of struts in plan view, s = 3 m. a. Using Pecks empirical pressure diagrams, draw the earth-pressure envelope. b. Determine the strut loads at levels A, B, and C.
Determine the theoretical embedment depth for the given free support anchored sheet pile wall placed in sand. 7m Dredge line D Ground surface 1 m SAND =30° C = 0 Yn 18.0 kN/m³
In Problem 14.6, assume that Dactual = 1.3 Dtheory.a. Determine the theoretical maximum moment.b. Using Rowe’s moment reduction technique, choose a sheet-pile section. Take E = 210 x 103 MN/m2 and σall = 210,000 kN/m2.
A cantilever sheet pile supports a horizontal backfill having a height of 4m. Unit weight of the backfill is 18 kN/m3. Angle of friction of backfill is 34°. a. Compute the depth of embedment required for stability of cantilever using factored strength method.b. Compute the total lateral active force on the sheet pile.c. Compute the total passive force on the sheet pile.
PROBLEM NO. 2 A cantilever sheet pile wall is supporting a horizontal backfill having a unit weight of 18 kN/m³. Active pressure coefficient K, = 0.28 and a passive pressure coefficient Kp = 4.6. (1) Determine the value of "d" required for stability of the cantilever sheet pile using the Factored Moment Method (FMM). The Factor of Safety on passive resistance is 2, (2) determine the value of "d" required for stability of the cantilever sheet pile walls using the Factored Strength Method (FSM), (3) determine the value of “d* required for stability of the cantilever sheet pile walls using the Net Passive Pressure Method (NPPM). The Factor of Safety for lateral forces causing rotation is 1.5. Page of 3m Figure 2. Sheet pile profile