5-74 A rod is made from two segments: AB is steel and BCis brass. It is fixed at its ends and subjected to a torque ofT 680 N m. If the steel portion has a diameter of 30 mm,determine the required diameter of the brass portion so thereactions at the walls will be the same. G = 75 GPa, Gbr39 GPa.5-75 Determine the absolute maximum shear stress in theshaft of Prob. 5-74.CB1.60 m680 N-mA0.75 m

Dbrass = 42.70mmτmax = 64.13MPaExplanation:

Answered: 5-74 A rod is made from two segments:…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that Es = 200 GPa and E,= 100 GPa, determine (a) the reactions at A and E, (b) the stress at segment BC, (c) the deflection of point D. Dimensions in mm 100 100 -180- -120- A Cl Dl E Steel B Brass 60 kN 40 kN 40-mm diam. 30-mm diam.
022 Plate 3-Method of Consistent Deformation Determine the force in member CD of the truss shown in the figure. Circled values are areas in square inches. E is constant. FEU ALASANC FEU DEIMAN What is the horizontal Reaction at A? [Select] What is the Verticall Reaction at A? [Select] What is the Vertical Reaction at B? [Select] What is the horizontal Reaction at C? [Select] O II W -10 ft- B D 30 k (2) Wo -15 ft S 0 C 20 ft C Technology Driven by Innovation 208C Light rain
The aluminum rod AB (G=27 ???) is bonded to the brass rod BD (? =39 ???). Portion CD of the brass rod is hollow and has an inner diameter of 40 mm. Determine (a) the angle of twist at B. (b) the angle of twist in A
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 94 GPa] with a cross-sectional area of A1 = 510 mm?. Bar (2) is an aluminum alloy [E = 74 GPa] with a cross-sectional area of A2 = 380 mm?. A concentrated load of P = 89 kN acts on the structure at D. Assume L1=770 mm., L2=620 mm., a=690 mm., b=350 mm., and c=1220 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar.
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 110 GPa] with a cross-sectional area of A1 = 520 mm?. Bar (2) is an aluminum alloy [E = 67 GPa] with a cross-sectional area of A2 = 280 mm?. A concentrated load of P = 88 kN acts on the structure at D. Assume L1=800 mm., L2=390 mm., a=510 mm., b=300 mm., and c= 1130 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vo of point D on the rigid bar.
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 102 GPa] with a cross-sectional area of A₁ = 530 mm². Bar (2) is an aluminum alloy [E = 68 GPa] with a cross-sectional area of A2 = 370 mm². A concentrated load of P = 50 kN acts on the structure at D. Assume L₁-930 mm., L₂=500 mm., a=600 mm., b=260 mm., and c=1150 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. b (a) 0₁ i = MPa, 0₂ = i MPa (b) VD = i mm. e L₁ L2 Ⓡ B C
Q1: A torque T = 4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa. Determine: (a) maximum shearing stress in the in the steel core. (b) the maximum shearing stress in the aluminum jacket. (c) the angle of twist at A. 172 mm 54 mm- A Steel core- 25 m Aluminum Q2: aluminum rod AB (G=27GPa) brass rod BD (G= 39GPa). portion CD of the brass rod is hollow and has an inner diameter of 40 mm, Determine: a) the angle of twist at A. b) maximum shear stress of rod AD c) torque diagram d) angle of twist diagram 60 mm TB 1600 Nm 36 mm T₁ = 800 Nm. 400 mm q+ 375 mm 250 mm
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 92 GPa] with a cross-sectional area of A₁ = 680 mm². Bar (2) is an aluminum alloy [E = 74 GPa] with a cross-sectional area of A₂ = 350 mm². A concentrated load of P = 56 kN acts on the structure at D. Assume L₁=900 mm., L2=600 mm., a=580 mm., b=310 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. b Answers: (a) o₁ = (b) VD= i i L₁ L2 (2) B C MPa, 0₂ = mm. i D MPa
(b) Resolve R into the normal component P (normal to the cross-section of the shaft) and the shear component V (in the plane of the cross-section)
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 116 GPa] with a cross-sectional area of A₁ = 550 mm². Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A₂ = 290 mm². A concentrated load of P = 62 kN acts on the structure at D. Assume L₁=800 mm., L2=560 mm., a-590 mm., b=430 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a b Answers: (a) σ₁ = (b) VD = i (1) L₁ L2 (2) A B MPa, 0₂ = mm. D MPa
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 113 GPa] with a cross-sectional area of A₁ = 600 mm2. Bar (2) is an aluminum alloy [E = 77 GPa] with a cross-sectional area of A2 = 300 mm². A concentrated load of P = 56 kN acts on the structure at D. Assume L₁-800 mm., L₂-580 mm., a-570 mm., b=340 mm., and c=1090 mm. Determine: (a) the normal stresses 0₁, 0₂ in both bars (1) and (2). (b) the downward deflection VD of point D on the rigid bar. a 5 Answers: (a) o₁ = (b) VD= i i e L₁ L2 A B C C MPa, 0₂ = mm. i D P MPa
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 110 GPa] with a cross-sectional area of A₁ = 630 mm². Bar (2) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₂ = 340 mm². A concentrated load of P = 52 kN acts on the structure at D. Assume L₁=910 mm., L₂=430 mm., a=450 mm., b=280 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a 5 Answers: (a) 6₁ (b) VD= = tel i (1) L₁ L2 B C MPa, 0₂ = mm. i MPa

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS