4. A voltage regulator circuit is shown on the right. The resistor value is chosen to obtain an output voltage (across the diode) of 0.7V. Use the diode small-signal model to determine the change in the output voltage when the supply voltage, V+, changes by IV. (This quantity is known as the line regulation and is generally expressed in mV/V) Hint: The answer will be only a function of V+ V+ ▷ l' R

4. A voltage regulator circuit is shown on the right. The resistor value is chosen to obtain an output voltage (across the diode) of 0.7V. Use the diode small-signal model to determine the change in the output voltage when the supply voltage, V+, changes by IV. (This quantity is known as the line regulation and is generally expressed in mV/V) Hint: The answer will be only a function of V+ V+ ▷ l' R

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit shown below, sketch to scale the output V waveform and draw the transfer characteristic (V versus Vi), Assume the diodes are ideal.
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
Using ideal diodes (voltage drop across ideal diodes is zero) and resistors, construct a circuit that results in the following output vs. input voltage characteristics.
Design a clipper circuit to clip off the portions of an input voltage that fall above 3 V or below -5 V. Assume that diodes having a constant forward drop of 0.7 V are available. Ideal Zener diodes of any breakdown voltage required are available. Dc voltage sources of any value needed are available.
For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KN resistor) and the load current (through the load 2.2 Kn resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode DI). The input V. is sinusoidal with maximum amplitude (peak) of 100 V and frequency of 700 Hz. The diode DI is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi
Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
3) Demonstrate clipping of negative waves with an inverted diode in the output. A circuit which removes the peak of a waveform is known as a clipper. Show a negative clipper. Produce a schematic diagram with LTspice schematic capture program. During the positive half cycle of the 5 V peak input, the diode is reversed biased. The diode does not conduct. It is as if the diode were not there. Show the positive half cycle is unchanged at the output V(2). Show the output positive peaks overlays the input sinewave V(1). Use in the LTSPICE display module, the command "plot v(1)+1)" accomplishes this. Voltage values: Resistor valuse: 1 ΚΩ DC offset: 0 V Amplitude: 5 V Freq: 1 KHz
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
Demonstrate clipping of negative waves with an inverted diode in the output.A circuit which removes the peak of a waveform is known as a clipper. Show a negativeProduce a schematic diagram.During the positive half cycle of the 5 V peak input, the diode is reversed biased. The diodedoes not conduct. It is as if the diode were not there. Show the positive half cycle isunchanged at the output V(2). Show the output positive peaks overlays the input sinewaveV(1).Voltage values: Resistor valuse: 1 K ΩDC offset: 0 VAmplitude: 5 VFreq: 1 KHz
Refer to the circuit. Consider ideal model (V_D=0) of diode circuits. Given V_i =100 Volts peak-to-peak sinusoidal input (+50, -50 Voltage peaks). Determine the peak output voltage during the diode non-conduction cycle.
In the circuit below, sinusoidal input voltage with a peak value of 10V is applied. Calculate the current flowing through the diodes D1 and D2 by drawing the waveform of the output voltage. (Both diodes will be considered ideal and Vc=5V).