3. Two steel plates with Sy = 45 ksi are attached by parallel-loaded fillet welds. Each weld is 5 in. long. E70 series welding rods are used, and good welding practice is followed. What minimum leg length must be used if a force of 10,000 lb is to be applied with a safety factor of 2? F B с D

3. Two steel plates with Sy = 45 ksi are attached by parallel-loaded fillet welds. Each weld is 5 in. long. E70 series welding rods are used, and good welding practice is followed. What minimum leg length must be used if a force of 10,000 lb is to be applied with a safety factor of 2? F B с D

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter13: Flux Cored Arc Welding

Section: Chapter Questions

Problem 12R: What is the maximum plate thickness that an FCS weld can be made with 100% penetration without...

See similar textbooks

Related questions

Q: Evaluate the force needed to hold the splitter plate in place.

Q: A 0.9 m diameter vertical cylindrical tank which is 1 m high and is open to the atmosphere contains…

Q: 1. Shown frontloader is 5000 kg and lifts 800 kg. this symbol shows the center of gravity or center…

A: The mass of frontloader is The mass of load is

Q: 2. In Problem Set 3, Problem 2, we expanded superheated steam across a steady flow adiabatic turbine…

A: The inlet condition of the stream is,To find the adiabatic efficiency of the original turbine.

Q: 5. A motor is using a large pulley to pull a crate with a mass of m= 200 kg up a 30 degree incline.…

A: Given :The mass of crate is The mass of pulley is The radius of pulley is The radius of gyration is…

Q: A two storey building has two faucets, one in the basement and one in the firstfloor. The maximum…

A: The objective of this question is to find the maximum velocity of water at the first floor faucet…

Q: If the tension in cable DE is 455 N, determine the moments of this tensile force (as it acts at…

A: Given : The coordinate point are,

Q: 1. One kg of air is heated and compressed in a piston/cylinder system from 400 K, 100 kPa to 1200 K,…

A: For the solution refer below images.

Q: The motion of a particle is defined by the equations x=(+1)² and y = 4(t+1)2, where x and y are…

A: The equation of particle is

Q: Problem 2.18 Determine the true anomaly of the point(s) on an elliptical orbit at which the speed…

A: Given:The speed in an elliptical and circular orbit is the same, i.e,

Q: n the pressure vessel experiment, the readings (µε) in the strain gauges #1, #2 and #6 are 213, -76…

Q: Problem 1: Please determine the moment generated at O from the force applied to the triangular rigid…

Q: Consider an ideal gas with constant cp =R and in an initial state at 300K and 100 kPa. (a) Compute…

Q: Given the hook-up drawing, list all the equipment, tools and materials that are needed in…

Q: Calculate the Grashof condition for the following fourbar mechanisms. For each mechanism, specify…

A: The objective of the question is to determine the Grashof condition for the given fourbar mechanisms…

Q: 2. The yoke-and-rod connection is subjected to a tensile force of 5 kN. Determine the average normal…

Q: DETAILS 1-11 Consider a frictionless track as shown in the figure below. A block of mass m₁ = 5.65…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: The compound beam is fixed at A, pin connected at B, and supported by a roller at C. Draw the shear…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: The state of stress at a point in a structure is shown on the following element. Determine the…

Q: Determine the equivalent force and moment at point o 5ft 2 2016 10 16 30 40 16

Q: What is the ideal Otto-cycle efficiency for a 8:1 compression ratio, and how does it compare to the…

A: Given :The flame temperature is The compression ratio is

Q: An A-36 steel beam of following cross section is part of a bridge and it is subjected loading as…

A: The maximum moment is The cross section dimension are

Q: The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly…

A: List down the given data.The outer diameter of copper is The inner diameter of copper is The torque…

Q: 33.2 solve using MATLAB. do not use syms.

A: Sure, I can help you with that.The system of equations is:dx/dt = y dy/dt = -a*y - b*u where:x is…

Q: For the given loading, determine the force in members CD, CJ, and KJ of the Pratt roof truss and…

Q: 4. A pair of connected pulleys receive a force F = 75 N and P = 150 N as depicted in the image. The…

Q: Needs Complete typed solution with 100 % accuracy.

A: The objective of this question is to calculate the moment created by the force applied by the…

Q: Po AT Problem 2. The deformable bar of length 2a, Young's modulus E, coefficient of thermal…

A: The distributed load intensity per unit length is for The uniform temperature change is for The…

Q: The traffic light shown below is supported by a system of cables. Points A and B are in a vertical…

A: The dimension are The mass of traffic light is

Q: A pump is cavitating at its inlet (i.e., on the suction side). The fluid is water at 120°F. The…

A: Given : The temperature of fluid is The atomsphere pressure is

Q: A basketball leaves a player's hands at a height of 2.20 m above the floor. The basket is 3.05 m…

Q: ! Required information Steam enters the high-pressure turbine of a steam power plant that operates…

A: Given:The pressure at the inlet to the high-pressure turbine, The temperature at the inlet to the…

Q: A hydroelectric generation facility has a gross head of 120 m and a consistent yearlong water flow…

Q: A heat engine using air starts with p1 = 3 atm and V1 of 5 L. Its pressure increases at constant…

A: Ans Given Now draw the P-V diagram of the heat engine asNow calculate the temperature at point 1…

Q: The velocity field for a flow of water is defined by u = (0.8z) m/s, v = (0.4tx) m/s, and w = (0.3z)…

A: Given-

Q: Q3: Determine the maximum positive moment and the maximum negative moment at B caused by the moving…

A: The objective of this question is to determine the maximum positive and negative moments at point B…

Q: a. Draw the free-body diagrams and write the differential equations of motion for the two masses in…

Q: The point in the immersed body through which tje resultant pressure of the liquid may be taken to…

Q: A stepped bar is held in equilibrium by several forces acting at different points along the length,…

Q: wo insulated Tanks are connected with an insulated pipe and a valve. The valve is open and steam…

Q: The 1 inch diameter rod is subjected to the loads shown below. Determine the state of stress at…

Q: If the speed of the train is uniformly increased from 6 mi/h to 8 mi/h in 1 min, determine the…

A: The radius of the circular track, (R)=2300 ftThe change in speed from 6 mi/h to 8 mi/h in 1…

Q: The block members have a cross section of 2 in x 2 in is joined by a glued scarf spliced as shown.…

A: The ultimate normal stress on the glue surface is The factor of safety is The cross section…

Q: please help me solve and explain

Q: A model of a helicopter rotor has four blades, each of length 3.5 m from the central shaft to the…

A: The length of blade is The rotational speed is

Q: 3. The ropes and pulleys shown are very light and there is no friction. The 5 N block B and 50 N…

A: The weight of block A is The weight of block B is .The system is releasaed from rest.

Q: find the speed up with which it flows inside the hose.

Q: The arm ABCD is subject to the forces shown. A. Find the sum of moments around point D (∑?? B.…

Question

Parvinbhai

3. Two steel plates with Sy = 45 ksi are attached by parallel-loaded fillet welds.
Each weld is 5 in. long. E70 series welding rods are used, and good welding
practice is followed. What minimum leg length must be used if a force of 10,000
lb is to be applied with a safety factor of 2?
B
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Determining the given data

VIEW

Step 2: Finding throat area & allowable yield strength

VIEW

Step 3: Finding minimum leg length size

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

When estimating weld cost, what weld joint design factors should be considered?
Can a tee weld be strong if the welds on both sides do not have deep penetration? Why or why not?
Does all of the heat produced by an SMA weld stay in the weld? Why or why not?
What are the advantages of making vertical down welds?
How is the strength of a seam weld specified?
List factors that affect the cost of producing weldments.
What arc problems can occur in deep or narrow weld joints?
As stricter standards are applied to the welding process, what happens to the cost of the weldment?
When a weld is oversized, what joint failure problem can result?
Sketch 2 NDT symbols illustrating different methods that can be used to indicate multiple test requirments for the same section of weld.
Answer the following questions (use free hand sketch) What is mean by M24 X 2-RH 2-What is the function of a cover plate in riveted joints? 3- If a weld is to have a flat finish, 4-A key is a temporary joint (True/False). should be added above the symbol. 5- Taper sunk key is tapered on both sides (True/False). 6- Give the suitable welding symbol for figure below
An axially-loaded welded angular connection is shown SD-002 . The angular section 150 x 100 x 10 mm having an area of 2400 mm? is welded to a gusset plate having a thickness of 10 mm. All steel is A 36 (Fy = 248 MPa, Fu = 400 MPa) and E (70) electrodes (Fu = 484 MPa) is used. Using the shielded metal-arc welding process. Compute the value of "a" if T = 500 kN. (Please do not round-off to whole number the required thickness, use the exact (2 decimal) value.) 150 mm SD-002