3. Three concrete pipes are connected in series as shown, if the rate of flow in the pipe is 3.53 cfs. Determine the total headloss in the pipes Pipe 1 2 3 n Diameter (in) 8 6 10 0.012 0.011 0.013 hfr = 420.1042 cfs Length in (ft) 1250 985 1970 1 2

3. Three concrete pipes are connected in series as shown, if the rate of flow in the pipe is 3.53 cfs. Determine the total headloss in the pipes Pipe 1 2 3 n Diameter (in) 8 6 10 0.012 0.011 0.013 hfr = 420.1042 cfs Length in (ft) 1250 985 1970 1 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A prismatic bar is fastened between two rigid walls at A and B and subjected to loads as shown in…

Q: A wooden pile is being driven with a drop hammer weighing 30 kN and having a free fall of 1 m. The…

A: Weight of drop hammer = 30 kNFree fall = 1.0 mPenetration in last blow = 5 mmTo find:Load-carrying…

Q: Find the location of the centroid of the following shape: 90 mm 30 mm 70 mm X k 30 mm 30 mm y n…

Q: Final moment values got through the analysis of a portal frame have been shown in the figure. What…

A: We have to determine the value of X

Q: A 13.345 N block, initially at rest at point A, slides along the smooth parabolic surface. Determine…

A: Mass of block= 13.345 N

Q: b- Mark the following statement with True or False: 1. The protection works are now designed in…

A: This question is related to Water resources engineering from Civil Engineering.This is TRUE &…

Q: Two squirrels are sitting on the rope as shown. The squirrel at A has a weight of 1.2 lb. The…

Q: For a constant head laboratory test on a fine sand, the following are the given values: Length of…

Q: A square foundation in a sand deposit measures 1.22 m x 1.22 m in plan. Given: D = 1.52 m, soil…

Q: A vertical curve is required for a 1st class 3x3 highway section with entering and exiting grades of…

A: The entering and exiting grades of + 5.10% and -6.40%, respectively.The point of intersection of the…

Q: Figure 2 shows a reticulation system. Estimate the flow rate in each pipeline using Hardy-Cross…

A: pipelength L (m)diameter D (m)AB9000.25BC7500.2CD9500.25DA7500.2

Q: An unconfined cylindrical specimen of clay fails under an axial stress of 240 kN/m2. The failure…

Q: y as shown in the following figure, find its stress component. 0 X qr

A: An element is loaded as followsstress components has to de determined.

Q: A soil layer consists of 4m upper layer of dry sand have a Gs= 2.64 and a void ratio of 0.53 and a…

Q: I'm A Fi m B m C m 3 m P=(100+K) kN A rigid AD bar is suspended by two wires as shown in the figure.…

Q: Calculate the total strain when the stress was removed after 3 sec.

Q: Determine the height h above the base of the centroid of the cross-sectional area of the beam.…

Q: A parcel of land has been surveyed in the field and the lengths and bearings of the various sides…

A: The values given in the question are as follows:LinesBearingDistance(m)ABN 53o 27' E59.82BCS 66o 54'…

Q: 1/₂ B 1/₂ D 1/2. ( compute by and DD.

Q: m Water is flowing through a horizontal pipe of diameter 150mm at a velocity of 2-. A circular solid…

A: Given:Pipe diameter, D = 150 mm = 0.15 mVelocity of flow, V = 2 m/sDiameter of solid plate, d = 120…

Q: Design an I section purlin for an industrial building, with Galvanized iron sheets as the roofing…

A: Reinforced concrete is defined as the embedding of steel in concrete so that the two materials work…

Q: Find out the strength and efficiency of a bolted lap joint .The bolts are of 30mm diameter, grade…

A: Diameter of bolt, d= 30 mmDiameter of bolt hole, do=30+2.5=32.5 mmFor bolts of grade 4.6 fub =400…

Q: H.W: An open tube is attached to a tank, as shown in the figure. If the water rises to a height of…

A: Given:- Height of water= 800 mm

Q: Two vertical rods, one of steel and the other of copper, with cross-sectional areas 500 mm² and 1000…

A: Cross sectional area of steel (As) = 500 mm2Cross sectional area of copper (Ac) = 1000 mm2Total load…

Q: Determine the reactions and draw the shear and bending moment diagrams for the structure shown using…

A: Rb=37.5Rd=37.5

Q: 5. A vertical rectangular gate as shown is 3 m wide and 6 m high is hinged at the top, has a sea…

Q: 100cm T gem cm 10 Section cm 0.0K Rigid Plate a₁ 16.10-61/Cº a2=12.10-61/Cº Ei=100 GPa E2=200 GPa…

Q: SUBJECT: FUNDAMENTAL OF ENGINEERING MECHANICS Q1 PLEASE ANSWER AS SOON AS POSSIBLE

A: The objective of this question is to understand the applications of the area moment of inertia, also…

Q: 1. 'Water flows through a 12 inches by 6 inches venturi meter at the rate of 1.49 ft/s and the…

Q: Q2: A column analysis for an activated sludge su MLSS Conc (mg/l) Settling velocity m/h 1000 2.8…

Q: X- 18 cm Mx y 10 cm 18 cm 3 cm 2 cm 16 cm 2 cm 2 cm 10 cm A bending moment of magnitude M₁ = (6+K)…

A: An I section type beam is given with bending moment = 23 Kn-mAssume the moment is sagging Hence…

Q: O kN are placed on the floor beams. If the beams also sup ad of 700 Nm, determine (a) the maximum…

Q: A silo of grains of 6.0 m in diameter and its height is 21 m. This silo exerts a load per unit area…

A: qapplied = 160 kPaCu = 24 kPaB = 7.2mdf = 1.52m

Q: Variable X in this question is that last digit of your student ID. Enter X here: X = A shallow…

A: Given: water table is 5m below foundation.net ultimate bearing capacity =450kPa Here foundation is…

Q: Problem 2 Water at 60F ( 62.36 lb/ft and 7.536 * 104 lb/ft s) is flowing steadily in a 2-in-…

A: Flow rate (Q) = 0.2 ft3/sLength of pipe (L) = 200 ftDiameter of pipe (D) = 2 in = 2/12 ftDensity of…

Q: or each of the building properties listed below, identify which parameter from the base shear…

A: This question is related to Base shear from Structural analysis from Civil Engineering.Find out…

Q: Given: A sample of clay soil of volume 1x10³ m² and mass 1.762kg, after being dried out in oven had…

Q: Q1/ An inward flow turbine with radial discharge has an overall efficiency of 80% and develops 150…

A: E = 80%P = 150 kW H = 8mN = 150 rpm

Q: Two drivers each have a reaction time of 2.5 seconds. One is obeying a 90 km/h speed limit, and the…

A: Reaction time of both the observer = 2.5 sec Velocity of car ( obeying speed ) = 90 km/h Velocity of…

Q: The normal stress (kPa) on a plane inclined at 30 degrees from the horizontal is most nearly (anti-…

Q: Dr. Example 7: A water plant treating 30000 m³/day. The rapid mixing is used tank blend 35 mg/L of…

Q: H.W. 1/Choose the correct answer for the following questions and show how you are make your choice.…

A: 1Q . Option A (equal to and less than )Explanation : According to Terzaghi, a foundation is shallow…

Q: An aluminum pipe with a length of 60 m at a temperature of 10°C rests freely on the ground. An…

A: Answer:- The length of the ALUMINUM pipe after the change in temperature can be expressed as by the…

Q: A rectangular beam has a width of 300mm and effective depth of 440mm. It is reinforced with 3-32…

Q: Q2- For the simply supported beam AB shown in Fig.(2), find length L so that ABS. moment is 350 kN.m…

Q: 4 m * 3 m 5m Wall Base Y sat = 17 kN/m³ cs = 20° Y sat = 18 kN/m³ $ = 30° Y sat = 17.8 kN/m³ cs =…

A: The coefficient of Rankine's active earth pressure is calculated by the following formula:The…

Q: calculation and draw SFD and BMD.

A: Determine the support reaction and draw the shear force and bending moment diagram of the given…

Q: In a geotechnical laboratory an oedometer test on a saturated clay soil was conducted. The results…

A: Cc=0.2Cr=0.04OCR=4.5

Q: How to find the measure of the lines? 60 degrees, 127 to 53 degrees, and 125 degrees. Area =…

A: A figure in which the area and perimeter arearea = 144.1672 perimeter = 71.8077needs to find the…

Q: thickness limitation. 1.8 Determine the design moment strength of the section sho MPa and fy = 400…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

3. Three concrete pipes are connected in series as shown, if the rate of flow in the pipe is 3.53 cfs.
Determine the total headloss in the pipes
Pipe
1
2
3
n Diameter
(in)
8
6
10
0.012
0.011
0.013
hfr = 420.1042 cfs
Length
in (ft)
1250
985
1970
1
2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data,

VIEW

Step 2: Formula

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 6: EGL and HGL (II) Part A Why is the energy gradient (i.e., the slope of the EGL=EL) larger in pipe 2 than in pipes 1 or 3? (<10 words) Part B Why are the EGL and HGL not parallel in this figure? (<10 words) H V² 28 HGL 2 EL Hydraulic grade line, slope = S, Ax - Energy line, slope = Sy Bed ylope Datum h₂ - Az 2 4 X
Q2: An otl of viscosity Co.15 pas) and specific gravity 0.9 is flows Throngh 1.Find The slope of The Pipe That will canse The Pressure to be constantalong The pipes entire length? an inclined (300mm) diameter Pipe. Q= 0.005m3/sec 3oomm Dia. Zz datum 2. check if The Rlow is laminarRlow?
pipe 310 m Water is flowing in a straight concrete lining centrifugally spun pipe as shown in the figure problem 12. The difference between the two gauge readings is 185 kPa. The flow rate is designed to be 30 liter/s. By using Darcy Weisbach and Hazen William's formula, determine the pipe diameter. (Ans.: 228 mm, 123 mm) TABLE 5.1: Pipe Characteristies Pipe Hazen-William* Roughness e (mm) 0.15 C 140 Asbestos Cement (AC) – all ages Cast Iron, Ductile Iron - new 0.3 130 10 years old - 20 years old 1.5 3.0 100 90 Cast Iron coated – good condition all ages Welded steel - uncoated - new 0.3 135 125 100 100 - old 0.6 1.5 Coal tar enamel coated steel – new Concrete lining centrifugal spun – all ages Galvanized Iron (GI), Mild Steel (MS) HDPE, UPVC, Polyethylene Wrought Iron Copper, Brass *The Malaysian Water Association - MWA (Design Guidelines for Water Supply Systems) 0.15 0.15 140 0.3 130 0.015 155 0.045 ND 0.0015 ND ND = No Data
& Determine the distribution of the flow in a pipe network Head doss may be assumed as Kg2.. The flow is К tue Mbudent and the pipes are sough. The value of is indicated. In the fig. use Hardy cross mtd. Solluc. 50d/sec. > A. K=2 K=2 B A. k=1 k=4 C K=3 251/sec. asllsec.
Problem 9-36 pipe bend shown is in a horizontal plane. A fluid weighing 8.615 kN/m enters the bend with a velocity of 3.5 m/s and a pressure of 280 kPa. Neglecting head loss, find the force required to hold the bend in place. The Ans 10.4 kN 65 200 mm O 80 mm diam
In the figure shown, the pipe entrance is sharp-edged, and the flow of water is 4 L/s. What is the total minor loss in the pipe? Use a roughness value of 0.25 mm for the cast iron pipe and a value of 1 x 10-6 m²/s for the kinematic viscosity of water. V Water 40 m O a. 13.88 m O b. 2.12 m O c. 2.22 m O d. 13.11 m Turbine Cast iron: L = 125 m, D = 5 cm Open globe valve
" ZAIN IQ H+ Exam c.docx → Exam Ql:- Using the dimensional analysis, find the relationship between the variables, shear stress t, flow velocity v, density p, viscosity u and pipe diameter D.
7.70 If the pipe shown has constant diameter, is this type of HGL possible? If so, under what additional conditions? If not, why not? HGL р Y Z Datum PROBLEM 7.70
Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section from point 1 to point 2, which is 1.5 m above point 1, at the rate of 0.9 m³/s. At section 1 the pipe dia is 0.5 m and pressure is 800 kpa. If pressure at section 2 is 600 kpa determine the pipe diameter at that location. (neglect the losses) tt thele loloses)
Solve for the water discharges in cach steel pipe as shown in Figure 3. You may assume that the minor losses (entrance, exit & bend losses) are negligible. Two trials are enough for this exam. -Elevation 35 m Pipe 1: D-0.2m, L=2400m, f=0.020 Elevation 30 m Elevated tank A -Elevation 28 m Elevated tank B Reservoir C Pipe 3: D=0.15m, L=1500m, f=0.020 Pipe 2: D=0.2m, L=2400m, f=0.020 -Elevation 10 m Figure 3
find Q ? and pressure at each pipe L: 7om dsolm L=ioum
Question 1: Determine the flows in the netw ork shown in Fig Q1, neglecting minor losses. Data: Pipe АВ BC BD ВЕ EF EG Length (m) 10 000 3 000 4 000 6 000 3 000 3 000 Diameter (mm) 450 250 250 350 250 200 Roughness of all pipes, Ks = 0.03 mm - 150 A 100 80 - 75 Figure Q1 60 G