3. Direct tension indicators are sometimes used instead of torque wrenches to ensure that a bolt has a prescribed tension when used for connections. If a nut on the bolt is tightened so that the six 3-mm high heads of the indicator are strained 0.1 mm/mm, and leave a contact area on each head of 1.5 mm², determine the tension in the bolt shank. The stress-strain diagram of the indicator material (and bolt) is shown.

3. Direct tension indicators are sometimes used instead of torque wrenches to ensure that a bolt has a prescribed tension when used for connections. If a nut on the bolt is tightened so that the six 3-mm high heads of the indicator are strained 0.1 mm/mm, and leave a contact area on each head of 1.5 mm², determine the tension in the bolt shank. The stress-strain diagram of the indicator material (and bolt) is shown.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The specifications for a coil spring are known. Infinite fatigue life is required, using a safety factor of 1.3 applied to the maximum load only. The fatigue strength can be represented by a line between τmax= 600, τmin= 0 and τmax= τmin= 900 MPa.Assume both end plates are in contact with nearly a full turn of wireand that the end plate loads coincide with the spring axis.Determine a suitable combination of d, D, and N, if C = 8
The gear forces shown act in planes parallel to the yz plane. The force on 20 in gear A is 300 lbf. Consider the bearings at O and B to be simple supports. For a static analysis and a factor of safety of 3.5, use both the DET and 16 in the MSST to determine the minimum safe diameter of the shaft. 10 in Consider the material to have a yield strength of 60 ksi. Gear A Solution: 24-in D. Gear C 10-in D. 20°
The induced nominal stress in a machine member is 28 N/mm? and the value of maximum stress near the irregularities is 61N/mm?, the value of stress concentration factor is SCF, K = Bearings are designated by a standard number internationally, the first digit in the bearing number 6409 represents type of the bearing. Select one: O True O False The value of curvature correction factor k; will be . if the spring index is 6. O a. 1.33 O b. 1.08 O c.0.,92 O d. 4.00 The figure below shows the components of normal forces, the value of radial force on the gear wheel due to a tangential force of 642 N is . N, Take pressure angle as 1420. Pitch point P. Gear driven 02 The radial force is
When in tune, a steel banjo string has a tension of 1300 N. If the ultimate tensile strength of the string is 600 MPa. What must be the minimum cross sectional area of the string so that it does not break? Allow a safety factor of 5.
For the lap connection shown, the rivets are 19-mm diameter and the plates are 8 mm thick. The rivets used are A502, Grade 1 and the plates are ASTM A36 with Fu = 400 MPa. Determine the value of Pin all possible modes of failure and the safe value of P that the connection can resist. Fv = 120 MPa, Fp = 1.2 Fu. Add 1.6 mm for the hole diameter. Ans. 297.6 KN
Situational Problem ( 3 - 4) An automobile engine develops 33.5 hp at 1,000 rpm. The clutch used to transmit this power in a single plate clutch with two pairs of contact surfaces. The coefficient of friction is 0.4 and the mean diameter of the disk is to be 190 mm. The average normal stress on the clutch lining is 120 kPa. 3. Determine the axial force to engage the clutch based on uniform wear. A. 1.57 kN B. 3.14 kN C. 5.28 kN D. 7.46 kN
The bolt AB in (Figure 1) has a diameter of 18 mm and passes through a sleeve that has an inner diameter of 42 mm and an outer diameter of 52 mm. The bolt and sleeve are made of A-36 steel and are secured to the rigid brackets as shown. If the bolt length is 220 mm and the sleeve length is 200 mm, determine the tension in the bolt when a force of 50 kN is applied to the brackets.
find the tensile of the bolt with diameter 38mm,80kN
Problem 5: At times in design, you would like to ensure that failure occurs in a specific part. For instance, in watch designs many components are stacked on top of one another due to the small space requirements. In this case if failure must occur, it is best that it happens in a gear that is easy to access. Using the maximum shear stress theory and only the stresses related to bending, determine the safety factors of the teeth on gears A, B, and C below. Each tooth can be assumed to be a rectangular cantilever beam with a point force at the end, the force can be determined using Torque = F x r. 0000 Gear B Gear C Gear A Torque on Shaft Gear Radius Tooth Length Tooth Height Tooth Thickness Gear A 10 N-mm 8.0 mm 1.5 mm 1.5 mm 0.5 mm Gear B 8 N-mm 3.0 mm 2.0 mm 1.5 mm 0.5 mm Gear C 6 N-mm 5.0 mm 1.5 mm 2.0 mm 0.8 mm Gear D Gear D 30 N-mm 10.0 mm 1.5 mm 1.5 mm Solve Material: Steel E =200 GPa Sy = 250 MPa
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures
A 2.5-in Aluminum plate and a 1.5-in cast-iron plate are compressed with one bolt and nut. The bolt is 3/8 in-16 UNC. (1) Determine a suitable length for the bolt, rounded up to the nearest 4 in. (2) Determine the bolt stiffness ks. (3) Determine the stiffness of the members km.
For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft. Assuming that the force that the nut needs to suppress is Fçak=1218 kgf (it was found in the previous question, but we don't use it), what should the minimum NUT HEIGHT be in mm to create this force safely? (Screw and Nut's surface safety pressure Pem=45 N/mm2 Screw base diameter d1= 21.5 mm. (Calculate the pitch (h=?) according to the given ones, considering that metric screw is used!)