22. A manufacturing process is controlled by a built in logic circuit which is made up of AND, OR and NOT gates only. The process receives a STOP signal(i.e. X = 1) depending on certain conditions, shown in the following table: A stop signal (X = 1) occurs when:eitherVolume, V > 1000 litres and Speed, S <= 15 m/sor Temperature, T <= 750°C and Speed, S > 15 m/s Draw the logic circuit and truth table to show all the possible situations when the stop signal could be received. INPUTS BINARY VALUES CONDITION IN PROCESS V 1 Volume > 1000 litres Volume <= 1000 litres T 1 Temperature > 750°C Temperature <= 750°C 1 Speed > 15 metres/second (m/s) Speed <= 15 metres/ second (m/s) %2

22. A manufacturing process is controlled by a built in logic circuit which is made up of AND, OR and NOT gates only. The process receives a STOP signal(i.e. X = 1) depending on certain conditions, shown in the following table: A stop signal (X = 1) occurs when:eitherVolume, V > 1000 litres and Speed, S <= 15 m/sor Temperature, T <= 750°C and Speed, S > 15 m/s Draw the logic circuit and truth table to show all the possible situations when the stop signal could be received. INPUTS BINARY VALUES CONDITION IN PROCESS V 1 Volume > 1000 litres Volume <= 1000 litres T 1 Temperature > 750°C Temperature <= 750°C 1 Speed > 15 metres/second (m/s) Speed <= 15 metres/ second (m/s) %2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 4: For the number display below, we would like to identify Boolean expression for LEDS (outputs a through g2) that indicate numbers 11, 14, and 15. a. Please write the Boolean expressions for the two LEDS (outputs a through g2) based on the input signals So to S3. You do not need to simplify the Boolean expressions. b. Please draw the logit circuit for outputs a through g2 a2 Logic circuit 2. 88 5,5,5,50
USE DIGITAL LOGIC AND DESIGN Part 1: In Figure_4; we have 4-bit Comparator using 2-bit Comparators block. You have to satisfy given condition by applying all data on figure 4. At the end, given condition should produce HIGH output and other two should be LOW. A3 A2 A1 A0 = 1101 and B3 B2 B1 B0 = 1110 Figure_4 Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from D0 through D3. Figure_5 Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input. Figure_6 Part 4: The data-input and…
In the electrical circuit given below, the state of the LED's illumination is logic 1. Since the state of pressing the A, B, C and D switches is logic 1, answer the requests. a) Obtain the output expression of the circuit in terms of minterms in its simplest form using the horn map method. b) Write the output function in terms of maxima. c) Obtain the output function obtained with Minterim only with AND NOT gates.
Solve the problem and simplify the output function using Quine–Mc Cluskey Methods. The following requirements must be met in solving the problem. Requirement:a. Truth Tableb. Timing Diagramc. Quine – Mc Cluskey Method d. Logic Diagram A private company wants to decide on a certain issue. Each of the four officials has an equal share of voting right. At least two of them must approve the solution in order to implement it. Each of them has a switch which closes to vote YES and open to vote NO.
Logic Design courses / EE200SP21 / General / Mid Term Examination Part II (Subjecti Compute the minimal products of sum and minimal sum of products expressions for following KMAP. Show your groupings on KMAP АВ CD 1 1 1 1 0. Instructions: You have to solve the answer by hand on paper, scan/take photo and upload it as a single file. Local Disk (D:) Mid Term Examinat.
ii) For the circuit shown in Figure B9, a. Find logic functions for Y and Z. b. Simplify function Z using Boolean algebra. Y Figure B9 AB
Problem Description Material A and Material B are collected in a tank. These materials are mixed for a while. Mixed product is then drained out through Outlet valve. Implement this in PLC using Ladder Logic programming language. Problem Diagram Diagram of a mixing tank -Agitator Motor Material A Material B Inlet Valve 1 Inlet Valve 2 Level Material B☐ Level Material A Mixing Tank LLS Outlet Valve Mixed Product
Use the following state diagram and create the state table for a synchronous to detect the sequence. The circuit has a single input, x, and a single output z. The output is logic-1 whenever the input sequence 1001 is detected, logic-0 otherwise. Note that overlapping sequences are allowed, Create the initial state table, and the complete state table. Write the equations for all the state variables and the output z. 1 so S1 S2 S3 Z=0 Z=1 State diagram of 1001 sequence recognizer
Q5: Determine the output boolean expression for logic circuit as shown in figure below. x- y- D z-
Use the following state diagram and create the state table for a synchronous to detect the sequence. The circuit has a single input, x, and a single output z. The output is logic-1 whenever the input sequence 1001 is detected, logic-0 otherwise. Note that overlapping sequences are allowed, Create the initial state table, and the complete state table. Write the equations for all the state variables and the output z. 1 SO s1 S2 S3 Z=0 Z=1
9. Design a combinational logic circuit: to convert Excess 3 (3-12) to BCD code (0-9). Note: Assume don't cares (X) wherever necessary in the simplification process
The sequential logic circuit may include a combinational logic gates circuit O True False