2. Water at 20°C (p = 998 kg/m³) flows through an inclined 8-cm-diameter pipe. At sections A andB, P₁ = 186 kPa, V₁ = 3.2 m/s, z₁ = 24.5 m, while pв = 260 kPa, VB = 3.2 m/s, and zB = 9.1 m.Which way is the flow going A to B, or B to A? Take acceleration due to gravity, g = 9.81 m/s².Show your work. f0.10.090.080.070.060.050.040.030.0250.020.0150.010.0090.008Laminarflow10³11---Transition range2(10³) 468104Moody ChartWholly turbulent flowSmooth2(104) 4 6 81052(105) 4 68Re=pVDμ1062(106) 4 6 81072(107) 4 6 80.050.040.030.020.0150.010.0080.0060.004 D0.0020.0010.00080.00060.00040.00020.00010.000050.00001

The pressure at section A,(PA)=186 kPa The velocity at section A,(VA)=3.2 m/s. The elevation at…

2. Water at 20°C (p=998 kg/m³) flows through an inclined 8-cm-diameter pipe. At sections A and B, P₁ = 186 kPa, V₁ = 3.2 m/s, z = 24.5 m, while pв = 260 kPa, VB = 3.2 m/s, and zB = 9.1 m. Which way is the flow going A to B, or B to A? Take acceleration due to gravity, g = 9.81 m/s². Show your work.

2. Water at 20°C (p=998 kg/m³) flows through an inclined 8-cm-diameter pipe. At sections A and B, P₁ = 186 kPa, V₁ = 3.2 m/s, z = 24.5 m, while pв = 260 kPa, VB = 3.2 m/s, and zB = 9.1 m. Which way is the flow going A to B, or B to A? Take acceleration due to gravity, g = 9.81 m/s². Show your work.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water enters a cylindrical tank through two pipes at rates of 141 and 126 gal/min (see the figure below). If the level of the water in the tank remains constant, calculate the average velocity of the flow leaving the tank through an 8-in. inside-diameter pipe. Section (2) 2₂= 141gal/min V 3= i 2.2712 D₂ = 8 in. Section (1) 21 = - 126gal/min Section (3) ft/s
A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -8 psi and 44 psi, respectively. The rate of flow in the pipe is 0.714 ft3/s. Neglect energy (friction) losses in the system. Use x = 4 ft., y = 7 ft. Use 1 hp = 550 lb-ft/s. Efficiency of the pump is 91%. What is the output power of the pump, in hp? Round off to two decimal places.
Q2/ A pump delivers water from a tank A (water surface elevation = 110 m) to tank B (water surface elevation = 170 m) as shown in figure below. The suction pipe is 45 m long ( = 0.024) and 35 cm in diameter. The delivery pipe is 950 m long (f = 0.022) and 25 cm in diameter. The head discharge relationship for the pump is given by H, = (90 – 8000 Q*), where H, in m and Q in m³/s. Calculate the discharge in the pipeline and the power delivered by the pump. Delivery pipe. elevation 170 m Suction pipe, elevation- 110 m Good Luck Rasha H. Salman
A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -8 psi and 44 psi, respectively. The rate of flow in the pipe is 0.714 ft3/s. Neglect energy (friction) losses in the system. Use x = 4 ft., y = 7 ft. Use 1 hp = 550 lb-ft/s. Efficiency of the pump is 91%. What is the input power of the pump, in hp? Round off to two decimal places.
A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -8 psi and 44 psi, respectively. The rate of flow in the pipe is 0.714 ft3/s. Neglect energy (friction) losses in the system. Use x = 4 ft., y = 7 ft. Use 1 hp = 550 lb-ft/s. Efficiency of the pump is 91%. What is the head in the pump (ft) ? Round off to two decimal places.
a! Water flowing through a tapering pipe having diameters of 300mm and 150mm at section one and two respectively. The discharge through the pipe 40 Liter/s. the section 1 is 10 m above the datum and section 2 is 6 m above the datum. Find the pressure at section 2if that at section 1 is 400 KN/m2. 10 6. m Datum
4. A pipe has an initial radius of 30cm, which then changes to a radius of 10cm. The velocity of the water in the initial part of the pipe is 2m/s. The segment of the pipe with the smaller radius is also 0.5 m higher than the initial pipe segment. What is the pressure difference between the two parts of the pipe? (6 pts) b) What is the volume flow rate in the pipe? (3 pts)
reservoir A is at elevation 90 m above datum, furnishes water to a 600 mm pipe which leads to a point at elevation 30 m, the pipe being 610 m long. Here it branches into three pipes, 200 mm, 300 mm, and 150 mm diameter. The 200 mm pipe runs 300 m and discharges to reservoir B at elevation 75 m, the 300 mm runs 450 m to reservoir D at elevation 30 m. f=0.012 what is the rate of flow towards reservoir B most nearly gives?
4. The system in Fig. consists of 1200 m (length) of 0.05 m (diameter) cast iron pipe, two 45° long-radius elbows, four 90° flanged long-radius elbows, and a fully open globe valve. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m³/s of water at 20°C into the reservoir? Average surface roughness of cast iron is ε = 0.26 mm. For water at 20°C, take density, p = 998 kg/m³; dynamic viscosity, μ = 0.001 Pa-s; and acceleration due to gravity, g = 9.81 m/s². 90° elbow: KL90, elbow K₁ = 0.5 ent Elevation (1 400 m = 0.3 45° elbow: KL45,elbow=0.2 Elevation 500 m ! Sharp exit Open KL = 10 globe valve Klexit = 1
i . In. 3º d 1 & 0:19 ぐ من ۱ Water flows steadily through a splitter as shown in the figure with volume flow rate of Q= 0.08 m/s and Q = 0.05 m/s. the diameter at section 1 and section 2 are (D3=D2= 12 cm) and the diameter of section 3 (D3= 10 cm). if the pressure readings are (P,= 100 kPa, P2= 90 kPa, P3= 80 kPa), calculate the force needed to hold the splitter at place. Disregard the weight effects. ابوالفظل 5:15p äclul 21.07.01 >
Water is flowing in a piping system as shown tin figure, Find the i. diameter of section 2 pipe. ii. Mass flow rate in section 1 Section 1 Q1= 0.4 m /s d1=30 cm Section 3 Q3=0.7 m/s V3= 5 m/s Section 2 V2=4 m/s d2=?
Measure the diameter of the pipe next to it, which goes from the discharge nozzle of a pump to the raised reservoir. The following data are known: • • • • • • L1 = 4m; L2 = 88 m; L3 = 75 m; L4 = 7 m. Maximum flow rate Q = 200 m³/h. Elevation elevations: Pump nozzle (H1) = 0.85 m Tank nozzle (H2) = 13.70 m Pump outlet pressure for the flow rate Q considered: P1 = 45 psig = 316 KPa. Maximum height of the liquid in the reservoir above point 2: Hr = 9 m. Maximum reservoir pressure: Pr = 10 psig = 70.3 KPa Specific weight of liquid: y = 9.5 N/dm³ • Kinematic viscosity: v = 550 cks EL. 13,70 my L4 L3 VG VR EL. 0,85 m P1