2. kütlelsr durgun halden a Her bir bloaun üZerine diyanrami), her bir blogun le- b) plardeki gerilumeleri bu Cevap

Q: A 65 kg person jumps from a window to a fire net 18 m below, which stretches the net 1.1 m. Assuming…

A:

Q: Momentum Equation Q1: What force components F, Fy are required to hold the block box in figure (1)…

A:

Q: À 400 N force is pushing a 100 kg box and makes it acceleration 0.5 m/sec^2. Find only the friction…

A:

Q: A 10.0-kilogram block sits on top of a high hill h1 = 10 meter and then slides down to a 4-meter…

A:

Q: Fluid mechanics, i need solutions in 10 minutes please. MCQ/ what is the specific weight of the…

A:

Q: A Locomotive starts from rest and pulls a train, weighing 20 X 106 N down a 1per cent grade. The…

A:

Q: A sled loaded with three people. Moving downhill on a hill. The hill surface has a friction force…

A:

Q: Wooden Воx A Non- Frictional Surface Non- Frictional Surface 60 Figure 2: Wooden Boxes Answer the…

A: (1) The free-body diagram of the system is given as, Now, on using D’ Alembert’s principle on mass…

Q: The super-container vessel in the figure has a total mass displacement of 23000 long tons. This…

A: Given: Mass m=23000long tons or (1016.05×23000)kg α=20° Tension applied on the vessel F=320kN Speed…

Q: (Homework's) atl A porter governor its central load is 18 kg and the weight of each ball is 2 kg.…

A: As per our Q&A guidelines we are supposed to solve only one question at once kindly repost the…

Q: d2- LP. осean Starting from rest, a penguin weighing 8kg, slides down a snowy incline at 57.2 to…

A:

Q: Assuming that there are no heat effects and no frictional effects,find the kinetic energy and speed…

A: Given data,  m= 3220 lb  H= 778 ft  There is no heat effects and no frictional effects

Q: na preliminary design for a mail-sorting machine, parcels moving at 2 fls slide down a smooth…

A: V=2ft/s=0.6096 m/sh=3ft=0.9144mμ=0.3k=176 lbf/ft=176×4.448220.3048k=2568.525…

Q: A ball is released from rest and rolls down an inclined plane, requiring 4.5 seconds to cover a…

A: Given data as per question Distance covered =100 ft Time is taken to cover distance =4.5 s

Q: A lift comes down from rest with an acceleration of 7 ft/s² into it attained a velocity of 21 ft/s.…

A:

Q: The figure shows three forces applied to a trunk that moves leftward by 2.63 m over a frictionless…

A: Given: The displacement of the trunk, s = 2.63 m The magnitude of horizontal force, F1 = 5.16 N The…

Q: Example (1-3): A jet of water 8 cm in diameter moving with velocity of 12 m/s strikes a flat vane…

A:

Q: In the figure, a 3.7 kg block slides along a track from one level to a higher level after passing…

A:

Q: The motorcycles mass: 170 kg The drivers mass: 64 kg I1= 0,26m I2=0,19m a) What is the needed…

A: Given: Masses of the motor cycle and driver are 170 kg and 64 kg. I1= 0,26m I2=0,19m

Q: A pulley 1 m in diameter rotating at 300 r.p.m is brought to rest in 80s. By constant force of…

A:

Q: asses al The friction force for both cases is 10 N. Find arms length and ne the range if speed in…

A:

Q: Find the size of a wind turbine rotor (diameter in m) that will generate 100kW of electrical power…

A:

Q: Friction Example, 1 A 3kg block starts from rest at the top of 30o incline and slides with a = 1.78…

A:

Q: You are designing a high speed elevator for a new skyscraper. The elevator will has a mass limit of…

A: The total mass, m=2400 kg Ascent speed va=18 m/s Descent speed vd=10 m/s Total vertical distance,…

Q: QI: The U tube (in Fig.1) is open at (D) and closed in (A). What will be the pressure at point (A, B…

A: Given: Given: The uniform acceleration to the top, az = 10 m/s2 The uniform acceleration to the…

Q: The block in the figure below has a mass m. The coefficient of static friction between the block and…

A: We have determine Smallest magnitude force

Q: 2. A rocket defined by displacement and accelaioation is fravelling in another planed where its…

A:

Q: 6- A water jet strikes a blade mounted on a lever as shown in figure. The value of the force F…

A:

Q: A force F=15 N is acting on a box at an angle a=20° with respect to the horizontal, as in figure 1.…

A: Given Data : Mass of jupiter (M)=1.9×1027 kg Distance between…

Q: A toy boat slides down a frictionless track and around a circular loop as shown in the diagram…

A: Given Data Mass of the boat, m=0.150 Kg The radius of the circular loop, R=14 cm The speed at point…

Q: For masses  and  are 200 kg, 300 kg, 240 kg, and 260kg respectively. The corresponding radii of…

A: Given Data

Q: Being a meticulous student, suppose you just want to consume the 772- calorie food that you ate…

A: Given data: Q=772 Caloriem=1865 kgd1=2 cmd2=25 cm Need to determine the vertical distance moved by…

Q: 500 N AY SOON Find the resultant system of converging forces in the figure. Below 200NX

A:

Q: A steel ball weighing 5 kg rolls horizontally at a rate of 10 m/s. If it rlls up an incline, how…

A: As per given  Mass=5kg Velocity =10m/s We have to determine how high up will it

Q: You push a 1.00 kg food tray through the cafeteria line with a constant 9.0 N force. The tray pushes…

A: Given Data The mass of the tray is: mT=1 kg The mass of the milk carton is: Mmc=0.5 kg Total mass…

Q: The first figure gives spring force Fx versus position x for the spring-block arrangement of the…

A: Given: The scale is set by the Fs=190 N. Calculation: (a) The slope of the curve is the spring…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.