2. Choose the assembler codes to move the value 5678h from physical memory location: 1234h to accumulator(DS=100h). a) mov ax, 1234h b) mov ax, 5678hc) mov ax, (1234h) d) mov ax, [5678h]e) mov ax, [234h] D mov ax, [4678h]

2. Choose the assembler codes to move the value 5678h from physical memory location: 1234h to accumulator(DS=100h). a) mov ax, 1234h b) mov ax, 5678hc) mov ax, (1234h) d) mov ax, [5678h]e) mov ax, [234h] D mov ax, [4678h]

Name: Explaionation not coding 2. Choose the assembler codes to move the val
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: Explaionation not coding 2. Choose the assembler codes to move the value 5678h from physical memory location: 1234h toaccumulator(DS=100h).a) mov ax, 1234h b) mov ax, 5678hc) mov ax, (1234h) d) mov ax, [5678h]e) mov ax, (234h) n mov ax, [4678h]

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Develop 8051 assembly program using a simulator to do the following: Read a sequence of ten 8-bit signed numbers stored in ROM, sum the absolute values of these numbers and store the 16-bit sum in RAM locations 40H (LSB) and 41H(MSB). Test your program with the following sets of data: a) -45, 88, -19, 16, 120, 79, -67, 48, 36,-93 b) 15, 80, -24, 156, 45, -120, 92, -110, 45,105
Complete the following table: MIPS Instruction op code rs rt rd shamt funct imm. /address Hexadecimal Representation add $t4, $s2, $s1 addi $s0, $t0, 123 lw $s6, -88($t7) Note: In MIPS register file, temporary registers $t0-$t7 have indices 8-15 (respec- tively). Also, the saved registers $s0-$s7 have indices 16-23 (respectively).
Convert given code to LEGv8 code:int f, g, y //global 64-bit variablesint sum (int a, int b) { // at memory address X0+1000.return (a +b)} int main (void) // at memory address X0 + 800{f=2;g=3;y= sum (f, g);return y;}Convert this code, making valid assumptions about registers and register use. Notethat brackets and global variable declarations are not affecting the addresses of the instructionsin memory.
Consider the following LEGV8 assembly code. Find the C code version of the assembly code fragment. Assume that the variables f, g, h, i, and j are assigned to registers X0,X1,X2,X3, and X4, respectively. Assume that the base address of the arrays A and B are in registers X6 and X7, respectively. ADDI X9, X6,#8 ADD X10,X6,XZR STUR X10.[X9,#0] LDUR X9.[X9,#0] ADD XO,X9,X10
Q5 Please convert the following C/C++ function to RISC-V assembly (RV321). Function: swap Registers: ra = x1 (return address) &v[0] -> a0 = x10 (arguments/return values) k-> a1 = x11 (arguments/return values) to = x5 (temporary) t1 = x6 (temporary) t2 = x7 (temporary) hint: void swap(int v[], int k) { int temp; temp = v[k]; v[k] = v[k+1]; v[k+1] = temp; %3D }
Ql'assuming the DS=1983 and SI-2284, BX-1325, BP-3425 and SS-1839, show the contents of memory locations after the execution? MOV CH,[BP]+23 MOV AX,[BX]+12
Assume that the state of 8088’s registers(in photos) and memory just prior to execution of eachinstruction follows: (b) SHL BYTE PTR [0400H], CL d) SHR BYTE PTR [DI+BX], CL (f) SAR WORD PTR [BX] [DI]+10H, CL
1) Consider these two lines from an assembly language program: PLACE .FILL X45A7 LDI R3, PLACE The assembler puts the translated version of the LDI instruction above into memory location x3025. After assembly is complete, what bit pattern is in memory location х3025 ? address instruction х3025 2) Now consider this line from an assembly language program: ASCII LD R1, ASCII The symbol table entry for ASCII is ×4F08. If this instruction is executed during the running of the program, what hex(with an x)adecimal value will be contained in register R1 immediately after the instruction just given is executed?
Suppose r0 = ox300010A0, r2 = 0x00000011, and the memory layout is as follows Address: Data: 0x300010A7 0x72 0x300010A6 0XA5 0x300010A5 0x9F 0x300010A4 0x00 0x300010A3 0x50 0x300010A2 0x2B 0x300010A1 0XA5 0x300010A0 0x01 -What is the Value of r0 and r1 after executing LDR r1, [r0, #2] -What are the values of r0 and r1 after executing the following code? Illustrate your process in a memory map. LDR r1, [r0], #3 ADD r1, r1, r2 STR r1, [r0, r#4]
Write an assembly code to assign the register BX with 4014H, and register DX with 4028 H. Move the content of BX to DX, und verse versa. Then, copy the now value of low content for BX and DX .to memory location [2131 H], and [2139H]
By assuming that X = 3, and 33 is a two digit number, consider memory storage of a 64-bit word stored at memory word 33 in a byte-addressable memory (a) What is the byte address of memory word 33? (b) What are the byte addresses that memory word 33 spans? (c) Draw the number 0xF1234567890ABCDE stored at word 33 in both big endian and little-endian machines. Clearly label the byte address corresponding to each data byte value.
Suppose r0 = ox300010A0, r2 = 0x00000011, and the memory layout is as follows Address: Data: 0x300010A7 0x72 0x300010A6 0XA5 0x300010A5 0x9F 0x300010A4 0x00 0x300010A3 0x50 0x300010A2 0x2B 0x300010A1 0XA5 0x300010A0 0x01 -What are the values of r0 and r1 after executing the following code? Illustrate your process in a memory map. LDR r1, [r0], #3 ADD r1, r1, r2 STR r1, [r0, r#4]