(2 2' 3 4 8570 PROBLEM 1 2720 3580 1500 (A 202 1 2 The Figure on the right is a 2nd Floor Structural framing Plan showing slabs, beams, and columns. Slab Panels were labelled accordingly. B 261 201 2800 Which among these slab panels act as ONE-WAY system? Which among these slab panels act as TWO-WAY system 201 201 6. 7 Show your solution in determining the slab classification. All measurements are in millimeters. D 8 10 201 201 201. E 2820 2850 2900 8570 1B 2ND FLOOR FRAMING PLAN S-1 S-1 SCALE 1:100

(2 2' 3 4 8570 PROBLEM 1 2720 3580 1500 (A 202 1 2 The Figure on the right is a 2nd Floor Structural framing Plan showing slabs, beams, and columns. Slab Panels were labelled accordingly. B 261 201 2800 Which among these slab panels act as ONE-WAY system? Which among these slab panels act as TWO-WAY system 201 201 6. 7 Show your solution in determining the slab classification. All measurements are in millimeters. D 8 10 201 201 201. E 2820 2850 2900 8570 1B 2ND FLOOR FRAMING PLAN S-1 S-1 SCALE 1:100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the type of this truss
Prepare the details estimate for the following 2 roomed building epare BOG the foilowing WI w1 D2 3500 mm x 3400 mm 4000 mm x 3400 mm W1 D1 D1 -Door 1 1100mmx 2100mm D2 -Door 2 1000mmx 2100mm W1-Window 1 1200mmx 1200mm Roof height: 2.80m Consider bearing for lintel as RCC roof 170mm thick Lintel 0.15m thick 300mm 1 300 mm 750 mm 1000 mmm- 1200 mm ww 00s ww 00s 200 mm ww 00s
THIS IS NOT A GRADED ACTIVITY. THIS IS JUST A REVIEWER FOR MY TRUSS DESIGN. THANK YOU SO MUCH!
Determine the required qty. rebar for this slab with a clear dimension of 5.6m x 7.8m SHORT SPAN (BAR SPACING IN MM.) LONG SPAN BOTTOM BARS (88) BOTTOM BARS TOP BARS CONT. (TBC) (BB) 300 200 #10 @250 SLAB MARK $17 THICK- BAR Ø NESS (7") 2V6 400x700 160 UNLESS OTHERS SPECIFIED 12 TOP BARS DISCONT. (TBD) 2H12 400x600 $17 (160) 2H14 400x600 2V11_400x650 40 C1 TOP BARS DISCONT. (TBD) (BAR SPACING IN MM.) TOP BARS CONT. (TBC) #10 @175 REMARKS TWO-WAY
Tie bars prblm
Compression member question.
We are designing a small office building with exterior siding finish: What is the code requirement for maximum spacing and nominal thickness of the direct to studs lap siding for 2”x4” framing? What must be for over sheathing of the shiplap edge panel siding? Use 2007 California Building Codes (CBC) to find the answers and post them. H2
What is the weight of the reinforcement in the longitudinal direction of the roof shown in the attached diagram, noting that the weight of the unit length of the iron is 0.888 kg /m to * the diameter of 12 and 0.618 kg / m to the diameter of 10 and 1.58 to the diameter of 16 6.75- #10@300 mm c/c $160350 mmjc/c 0160350 mn c/c 0100300 mm 4.75 0120250 mm c/c 0120250 mm c/c 0.25 0.25
PLEASE HELP! THIS IS NOT A GRADED ACTIVITY. THIS IS JUST A REVIEWER FOR MY TRUSS DESIGN. I'M THE ONE WHO MADE THE QUESTIONS. THANK YOU SO MUCH!
https://1drv.ms/b/s!AhpfTcuv_aegrXCGXD6TzN9xPS4x?e=TjkEba CISC Handbook of Steel Construction, available here for codes. please use these only. thanks.
List down installation process of tie beam
what is concrete formwork and shoring? (pls give me a detailed research about it)