A 150-lb block is placed on a 33° incline and released from rest. The coefficient of static friction between the block and the incline μsis 0.46. (a) Determine the maximum and minimum values of the initial tension T in the spring for which the block will not slip whenreleased. (b) Calculate the friction force F (positive if up the slope, negative if down) on the block if T = 108 lb.Assume W = 150 lb, 0 = 33º.Answers:(a) Tmax=(b) F = iӨilblb, Tminilb

Answered: Image /qna-images/answer/422b2865-7ea4-4aa4-8989-bd4588badd9d.jpg

150-lb block is placed on a 33° incline and released from rest. The coefficient of static fric 0.46. (a) Determine the maximum and minimum values of the initial tension T in the spring leased. (b) Calculate the friction force F (positive if up the slope, negative if down) on the ssume W = 150 lb, 0 = 33° nswers: ) Tmax= ) F= i W Ө i μ₂ lb lb, Tmin= i lb

150-lb block is placed on a 33° incline and released from rest. The coefficient of static fric 0.46. (a) Determine the maximum and minimum values of the initial tension T in the spring leased. (b) Calculate the friction force F (positive if up the slope, negative if down) on the ssume W = 150 lb, 0 = 33° nswers: ) Tmax= ) F= i W Ө i μ₂ lb lb, Tmin= i lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1: Calculate the axial stress in each part of this assembly if the ID of the steel tube 150mm, radius of the steel baseplate is 175mm and the concrete pedestal is replaced with a 200mm square concrete pedestal. If the steel tube is 3 meters tall and the pedestal is 1.25 meters tall, what is the deflection in each? Assume Econc = 25 GPa. 500 KIN -100 mm
1. *A propped cantilever has a 2m overhang. The beam has a load of 2W applied half way between the fixed support and the roller support and a load of W applied at the free end. What is the minimum value of W that will cause the beam to collapse? The beam has the cross-section shown below. The yield stress is 300 MPa. 75 mm 15 mm 300 mm 2W C D 15 mm 250 mm 15 mm, 2m B + 2m 2m
Question 8 20 Points Two plates each 25 mm thick and 130 mm wide are fastened by three 20 mm diameter rivets. Assume that the applied load P = 70 kN is distributed equally among the three rivets. Determine the tensile stress (MPa) in the plate at the critical section. ... P 000- P
Q:8/ A steel wire (10m) long, hanging vertically supports a tensile load of (2000N). Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed (140MPA) and the total elongation is not to exceed (5mm)..Assume (E=200GPA).
02: The rigid platform has negligible mass and rests on two steel bars, each 250.00 mm long. The center bar is aluminum and 249.90 mm long. Compute the stress in the aluminum bar after the center load P= 400 kN has been applied. For each steel bar, the area is 1200 mm2 and E= 200 GPa. For the aluminum bar, the area is 2400 mm2 and E 70 GPa Rigid platform Steel Ahmum Steel
Refer the beam shown with cross section of thickness, 1= 15 mm. If F = 84 kN and a = 150 mm, 2a 40a Determine the maximum stress in the cross section of the beam. Select the correct response: 300 MPa 280 MPa (200 MPa 187.5 MPa 122 2a
A solid steel shaft is transmitting 250hp at 1500 rpm a.) what should be its diameter if the deflection is not to exceed 1° for a length of 6 ft b.) what would be its ultimate stress if the factor of safety is 6? c.) if the shaft is hollow determine the dimensions of outside and inside diameters if (D=2d). d.) Compute the torsional deflection of the hollow shaft and determine which shaft is more rigid?
5.Compute the maximum shearing stress developed in a phosphor bronze spring having a mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. Assume G = 42 GPa. Use Wahl formula.
H.W2: A rectangular column of sides 0.4m×0.35m, made of concrete, is used to support a compressive load of 1.5MN. Four steel rods of each 24mm diameter are passing through the concrete as shown in figure 1.23. If the length of the column is 3m, determine the normal stress in the steel and the concrete. Take Esteel 200 GPa and Econcrete = 29 GPa. steel rod: 0 24 mm 0.4 m 3 m 0.35 m
The 400-kg uniform bar AB is shown in Figure is supported by a steel rod AC and a roller at B. If it supports a live distributed loading of 3 kN>m, determine the required diameter of the rod. The failure stress for the steel is sfail = 345 MPa. Use the LRFD method, where the resistance factor for tension is f = 0.9 and the load factors for the dead and live loads are gD = 1.2 and gL = 1.6, respectively.
1-21_Problems Q:1/ A hollow right-circular cylinder is made of cast iron and has an outside diameter of (75 mm) and an inside diameter of (60 mm). If the cylinder is loaded by an axial compressive force of (50 kN), determine the total shortening in a (600 mm) length. Also determine the normal stress under this load. Take the modulus of elasticity to be (100 GPa). Ans.(ô = 0.188 mm) , (o= 31.45 MPa) Q:2/A square steel bar is (50 mm) on a side and (250 mm) long. It is loaded by an axial tensile force of (200 kN). If(E= 200 GPa) and (µ= 0.3), determine the change of volume per unit volume. (Ans. 0.00016) Q:3/The bar shown in Fig.(1-22 ) is subjected to a tensile load of (160kN). If the stress in the middle portion is limited to (150N/mm³), determine the diameter of middle portion. Find also the length of the middle portion if the total elongation of the bar is to be (0.2mm). Young's modulus is given as equal to (2.1*10$ N/mm³). (Ans. d= 3.68em , L=20.71em) 160 KN A 6 cm DIA 160 N 6 om DIA…