15. A fluid in a closed system expands slowly according to the given relation U = 32+ 0.004 PV where U is in BTU, p in lbf /ft² abs, and V in ft³. When the fluid changes from an initial state of 30 psia, 1 ft3, to a final state of 65 psia, 3 ft³, compute the work and heat transfer in calories. 16. A certain fluid in a closed custom initial 6263

15. A fluid in a closed system expands slowly according to the given relation U = 32+ 0.004 PV where U is in BTU, p in lbf /ft² abs, and V in ft³. When the fluid changes from an initial state of 30 psia, 1 ft3, to a final state of 65 psia, 3 ft³, compute the work and heat transfer in calories. 16. A certain fluid in a closed custom initial 6263

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A certain ideal gas Y has molecular weight of 25 g/mol and specific heat ratio of 3. Initially, Y has pressure of 200kPa and volume of 2m3. The volume was doubled during heat transfer. Find the heat transfer if it underwent a process described by ( a. n=1 b. n=Cp/Cv C. n=2
1.5. A refrigerator is used to cool 4 litres of soft drink from room temperature (25 °C) to 3 °C. If the density of the soft drink is 1015 kg/m3 (1 litre = 0.001 m³), how much heat must be removed if the specific heat of the soft drink is 4350 J/kg °C. 1.6. An engine operating in a cycle absorbs 5000 cal of the heat from a heat source and performs 2000 cal of work. Calculate: (a) The amount of heat discarded in this cycle (b) The efficiency of the engine
isobaric process A certain gas, with cp = 0.529 Btu/lb -R and R = 96 ft lb/lb -R, expands from 5 cu meters and 80 deg F to 15 cu meters while the pressure remains constant at 15.5 psia. Compute the ff: a) Final Temperature, b) change in enthalpy, c) change in internal energy, d) change in entropy and e) non-flow work.
Given : STEADY STATE COMPRESSOR INLET PRESSURE: IN LET VOLUMETRIC AIR Ask: is elbf/in² FLOW RATE 5 ft³/s POLY TROPIC GOES THROUGH DIAMETER (INCHES) OF FOR EXIT PRESSURE AND EXIT VELOCITY OF PROCESS Pv¹.5 = constant EXIT PIPE 160 lbf / in 2 145ft/s.
1. A certain ideal gas X has molecular weight of 10 g/mol and specific heat ratio of 2. Initially, X has pressure of 20OKPA and volume of 2m3. The pressure was doubled during heat transfer. Find the heat transfer if it underwent a process described by a. n=infinity b. n=Cp/Cv c n=3
Q.3: The properties of a closed system change following the relation between pressure and volume as PV- 3, where Pis in bar, V is in m'. If the pressure increase from 1.5 bar to 7.5 bar. a. Drive an expression to calculate the work done during process. b. Determine the work for the process, in kJ.
3/ A piston-cylinder contain 5 kg of steam assembly undergoes an expansion from state 1, where the specific internal energy is u= 2709.9 kJ/kg, to state 2, where uz = 2659.6 kJ/kg. During the process, there is heat transfer to the steam with a magnitude of 80 kJ. Also, a paddle wheel transfers energy to the steam by work in the amount of 18.5 kJ. There is no significant change in the kinetic or potential energy of the steam. Determine the energy transfer by work from the steam to the piston during the process, in kJ. Skg of eam
mple 4.1 A stationary mass of gas is compressed without friction from an ini- tial state of 0.3 m' and 0.105 MPa to a final state of 0.15 m and 0.105 MPa, the pres- sure remaining constant during the process. There is a transfer of 37.6 kJ of heat from the gas during the process. How much does the internal energy of the gas change? 3 3
II. Constant Volume Process Problem: 4000 gal/min of saturated steam at 3.0 MPa undergoes a constant volume process at until the pressure becomes 4.0 MPa. Determine the following: A. Specific volume, m³/kg B. Temperature at point 1 and 2, °C C. Mass of steam, kg/s D. Au (kJ/kg), Ah (kJ/kg), and As(kJ/(kg-K)) E. Q (kW) F. Pv and ts diagram
A certain gas with Cp= 0.529 BTU/lbmole-Rankine and Cv= 0.4053 BTU/lbmole-Rankine expands from 20ft3 and 500 Rankine to 30 ft3 and 1620 Rankine its pressure remains constant at 40lbf/ in2 . R(gas constant)=97.24 ft3 -lbf/lbmole-Rankine Compute: a) Change of internal energy (BTU) b) Change of enthalpy (BTU) c) Heat Transferred (BTU)
1. a) Define thermal efficiency and give one example of heat engine. b) The graph in Figure 1.1 shows one mole of monoatomic gas at initial temperature of 40 ˚C and volume 2 L expanding isobarically at a constant pressure of 2.5 × 105 Pa to 5 L. It is then cooled down at constant volume to a pressure of 1.2 × 105 Pa. The gas is finally compressed isothermally back to its initial state. Calculate i. the work done in process AB. ii. the amount of heat absorbed from A to B. iii. the work done by the gas from C to A. iv. the total work done in the complete process.
In a piston-cylinder assembly, there is initially a pressure of 300 kPa, a temperature of 150oC and a volume of 0.5 m3 of air. Until air doubles in volume with PVn=constant polytropic processexpands as much. For n =1, n = k and n = 1.6a. final pressure of the air,b. Moving border work,c. Calculate the heat transfer.(Note: take constant specific heat values at room temperature (at 300 K).)