100 mm is to be turned at 200 rev/min and feedA batch of 500 jobs of diameter 50 mm and length0.2 mm/rev.Applying Taylor's equation VTO.25 = 160, the tool%3Dlife is minutes is(a) 20.36(b) 22.43(c) 674(d) 28.20

Given:Total number of jobs=500diameter, d=50 mmlength, l=100 mmN=200 rpmf=0.2 mm/rev

Answered: 100 mm is to be turned at 200 rev/min…

100 mm is to be turned at 200 rev/min and feed 50 mm and length A batch of 0.2 mm/rev. Applying Taylor's equation VTo.25 – 160, the tool %3D life is minutes is (a) 20.36 (b) 22.43

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

operation, the shear IS cIose to, In turning operation, spindle speed is set to provide a cutting speed of 2.2 m/: The feed and depth of cut are 0.32 mm and 2.1 mm, respectively. The tool rake angle is 15°. After the cut, the deformed chip thickness is measured to be 0.43 mm. Using the Orthogonal model as an approximation of turning operation, the shear strain is close to, In turning operation, spindle speed is set to provide a cutting speed of 2.4 m/
Q1:- Put a mark of True or false for below:- (a):- The milling cutting tool has a single cutting edge? (b):- At the break-even point, the total revenue equals the total cost? (c):- The right-hand rule is used to define machine axes? (d):- Design error is a simple mistake? (e):- The quality of products is poor in mass production? (f):- Allowances must be left before turning? (g):- Up-ward milling is better than down-ward milling?
P: For a certain job, the cost of metal cutting is 7 180 C/V and the cost of tooling is 270C/(TV), where Cis a constant, Vis the cutting speed in m/min and T is the tool life in minutes. The Taylor's tool life equation is VTO.25 = 150. The cutting speed ( in m/min) for the minimum total cost is %3D
Consider a milling process, where a pocket with width (X) of 400mm, Length (Y) 300mm, and depth (z) of 15 mm. The cutting tool is a 12 mm diameter flat end mill with 4 cutting edges. For some reason, the tool can be radially immersed in the material at most 50% of the tool diameter. The spindle speed is selected as 2000 rpm, where the max allowable axial cutting depth is 2.5 mm. a) Calculate the number of total cutting steps, indicating which feed direction would you prefer x or y. It may be preferred to have feed rate can be along X direction Total # of cutting steps: If feed direction is along X, the total number of cutting steps is 294 b) Calculate the minimum achievable cycle time if the feed rate is 0.15 mm/rev/tooth. Approx cycle time: 98 minutes
A HSS tool is used to turn a steel workpart that is 300 mm long and 80 mm in diameter. The parameters in the Taylor equation are: n=0.13 and C= 75 (m/min) for a feed of 0.4 mm/rev. The operator and machine tool rate = $30.00/hr, and the tooling cost per cutting edge = $4.00. It takes 2.0 min to load and unload the workpart and 3.50 min to change tools. Determine: a. Tutting speed for maximum production rate, b. Tool life in min of cutting, and c. Cycle time and cost per unit of product.
A HSS tool is used to turn a steel workpart that is 300 mm long and 80 mm in diameter. The parameters in the Taylor equation are: n = 0.13 and C = 75 (m/min) for a feed of 0.4 mm/rev. The operator and machine tool rate = $30.00/hr, and the tooling cost per cutting edge = $4.00. It takes 2.0 min to load and unload the workpart and 3.50 min to change tools. Determine: Tutting speed for maximum production rate, Tool life in min of cutting, and Cycle time and cost per unit of product. determine cutting speed for minimum cost.
Q4 Tool life of a turning tool is given by VT0.12xfP.7xd3=C at a cutting speed (V) of 25m/min, feed(f) 0.25 mm/rev and job diameter(d) 4 mm, the tool life was 53 minutes. Calculate (i) Tool life if cutting speed increased by 20 % [3]
4) Tool Life: A HSS tool has been used for a metal cutting operation shows a Taylor relationship of VT0.125-44.5. Originally 15 minutes were required to remove a dull tool. A new tool holder has made it possible to reduce the time to 5 minutes. What increase in cutting speed does this permit to obtain the maximum rate of production from the operation?
We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical milling machine and 50 cm from the edge. The width of the slot is 40 mm. TheDepth of the slot is 25 mm. For this, several rough cutting steps and aFine cut with a depth of 0.20 mm. The depth for each of the steps ofrough cut is limited to 1.75 mmAditional information:What is the number of blades used for the rough cutting steps?What is the number of blades used for the fine cutting step?
λ= te average Vc = MDN 1000 T = S sin Where λ is Chip Reduction Coefficient Vc is cutting speed te is thickness of cut chip T is thickness of non-cut chip S is feed rate Ⓒ is cutting angle = 45⁰ D is diameter of workpiece = 40mm Results m/min Depth of cut (a) mm 22222 Cutting speed (Vc) m/min 500 500 500 500 500 Feed rate (S) mm/rev Required: 1.Complete the solution to the table with the given rules 2-Draw chart between feed rate (S) and chip reduction coefficient 2 tc: tc₂ tcs 0.11 0.39 0.58 0.43 0.14 0.42 0.62 0.5 0.20 0.34 0.42 0.32 0.24 0.9 0.96 0.95 0.28 0.92 0.85 0.85 te average (mm) T (mm) with discuss it. Chip Reduction Coefficient (2)
3.Show the step-by-step process. Do not use shortcut methods. Make it as detailed as it can be. MAKE A DIAGRAM AND ENCODE THE ANSWER. DO NOT COPY CHEGG, THEY HAVE DIFFERENT GIVEN. HERE C=4 in
The length, width and thickness of a steel sample are 400 mm, 40 mm and 20 mm, respectively Its thickness needs to be uniformly reduced by 2 mm in a single pass by using horizontal slat milling. The milling cutter (diameter: 100 mm, width: 50 mm) has 20 teeth and rotates at 1200 rpm. The feed per tooth is 0.05 mm. The feed direction is along the length of the sample. If the over-travel distance is the same as the approach distance, the approach distance and time taker to complete the required machining task are