1. Study the ladder logic program in figure 2 below and answer the questions that follows What type of counter has been programmed? When would output "lot full light" energized? When would output "lot full light"de-energized? When will the count be incremented? When will the count be reset? Ladder logic program Enter L1 Inputs switch Output L2 CTU- COUNT-UP COUNTER Counter Preset Accumulated Lot full light Enter C5:1 150 switch Exit switch rCTD COUNT-DOWN COOUNTER Exit switch CS:1 Counter Preset Accumulated 150 Lot full C5:1/DN light Reset Reset C5:1 (RES) Figure 2

1. Study the ladder logic program in figure 2 below and answer the questions that follows What type of counter has been programmed? When would output "lot full light" energized? When would output "lot full light"de-energized? When will the count be incremented? When will the count be reset? Ladder logic program Enter L1 Inputs switch Output L2 CTU- COUNT-UP COUNTER Counter Preset Accumulated Lot full light Enter C5:1 150 switch Exit switch rCTD COUNT-DOWN COOUNTER Exit switch CS:1 Counter Preset Accumulated 150 Lot full C5:1/DN light Reset Reset C5:1 (RES) Figure 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ii) For the circuit shown in Figure B9, a. Find logic functions for Y and Z. b. Simplify function Z using Boolean algebra. Y Figure B9 AB
The following diagram shows a logic circuit using a combinatorial chip called A, and a sequential chip called B. Which wiring is legal, the wiring around chip A or the wiring around chip B. Select one: a. the wiring around chip A. b. the wiring around chip B.
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
9 Part 1 of 2 Mc Graw Hill Required information Consider the logic gate circuit shown in the given figure. A (S1)-0- B (S2)-0 C (S3)-0- AB B BC B+C What is the Boolean equation for the given figure? ***************** The Boolean equation for the given figure is (Click to select) Note: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.
Select a suitable example for for combinational logic circuit. O a. None of the given choices O b. De-multiplexer O c. PLA O d. Latches
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
12) Study the ladder logic program in the figure below and answer the questions that follow: a. What is the purpose of interconnecting the two timers? b. How much time must elapse before output PL is energized? c. What two conditions must be satisfied for timer T4:2 to start timing? d. Assume that output PL is on and power to the system is lost. When power is restored, what will the status of this output be? e. When input PB2 is on, what will happen? f. When input PB1 is on, how much accumulate. Ladder logic program Output PB2 L2 T4:1 Inputs (RES L1 T4:2 PB1 (RES) PLO PB2 -RTO - RETENTIVE TIMER ON PB1 Timer Time base Preset T4:1EN) 1.0 2900 CON) Accumulated -RTO- PB1 T4:1 RETENTIVE TIMER ON Timer Time base T4:2 (EN) 1.0 DN Preset Accumulated 1780 CON) T4:2 PL DN
12) Study the ladder logic program in the figure below and answer the questions that follow: a. What is the purpose of interconnecting the two timers? b. How much time must elapse before output PL is energized? c. What two conditions must be satisfied for timer T4:2 to start timing? d. Assume that output PL is on and power to the system is lost. When power is restored, what will the status of this output be? e. When input PB2 is on, what will happen? f. When input PB1 is on, how much accumulate. Ladder logic program Output PB2 L2 T4:1 (RES Inputs L1 T4:2 (RES PB1 PL PB2 -RTO PB1 RETENTIVE TIMER ON T4:1 EN 1.0 2900 CON) Timer Time base Preset Accumulated -RTO PB1 T4:1 RETENTIVE TIMER ON Timer Time base T4:2 (EN) 1.0 DN Preset 1780 ON) Accumulated T4:2 PL HE DN
For the logic diagram shown in Figure 2, find logic function Q prove it is equivalent to Ex-NOR gate. i. A- DDO B
What Is programmable logic arrays?
(b) Figure Q2(b) shows input waveforms of A, B and C. Draw the logic circuit that will generate the output waveform X. A Inputs B Output X Figure Q2(b) : Input and output waveforms
What are the properties of Logic Gates?