1. Obtain the state diagram and a primitive flow table for a circuit with two inputs X1 and X2 and two output Zland Z2 that satisfies the following four conditions:- i) When X1X2 =00 output Z1Z2=00. ii) When X1=1 &X2 changes from 0 tol, the output ziz2 =01. iii) When X2=1 &X1changes from 0 to 1, the output Z1Z2=10. iv) Otherwise the output does not change

1. Obtain the state diagram and a primitive flow table for a circuit with two inputs X1 and X2 and two output Zland Z2 that satisfies the following four conditions:- i) When X1X2 =00 output Z1Z2=00. ii) When X1=1 &X2 changes from 0 tol, the output ziz2 =01. iii) When X2=1 &X1changes from 0 to 1, the output Z1Z2=10. iv) Otherwise the output does not change

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Ex. 592. Refer to Figure 592. [R1,C1,S1,P1]=[ 0,15,0,0]. [R2,C2,S2,P2]=[ 5,14,0,1]. Determine A,B,C,D,E,F. ans:6
Q2 In the circuit as shown below. Determine the (ripple factor) and sketch vp(out) for the filtered bridge rectifier with a load as indicated. 2 : 1 D3 D1 120Vp-p f= 50HZ + Output V1 V2 D2 D4 1uf R1=2k
For the following zener clipper draw the output waveform Vz1 = 5V, Vz1 = 7V VK = 0.8v lkn ISV V₁₂ 5V 2, 72. -5V Q2 Determine The Output Waveform And Calculate The current and PIV 1kQ 1kQ 10 V 10 si www www Q. For the circuit shown in Figure below (1),find the maximum and minimum values of zener diod current. Live 5 ΚΩ www I IL 15 80-120 V 10 ΚΩ LIR 101 102 1015 S Ne 1 k0 www Iz 50 V U2 -ot V. Fumal inash
Draw a Signal Flow Graph equivalent of the Block Diagram shown in figure 1. R₁ (s) R₂ (8) R₂ (8) G₂ G₂ C(s)
Illustrate with the help of state diagram , state transitions for the specific inputs described in the state table below. Present Next State Output State x = 0 x = 1 A B B F C D A G E E H F D E G E H G H 0O O O O - -
A 3-bit binary weighted resistor DAC and a 3-bit R-2R ladder DAC have common values of Vref = 5V, R = 1kN, R = 2kN. Compare their output voltages for each of the following binary inputs. What do you observed? Binary Weighted Resistor DAC Resolution Binary input R-2R Ladder DAC Output voltage Resolution Output voltage 000 001 010 011 100 101 110 111
Realized a 4X1 multiplexer in the block diagram shown below. What is the output equation of the given multiplexer? Also draw the circuit diagram. N.B: Follow the instruction given in the figure to choose the input and output names. "First Letter of your Name"| 10 I1 | "Third Letter of your Name" 4X1 "Second Letter of your Name MUX 12 13 B
A 3-bit ADC with a reference of 10V is used to sample a DC signal. What is the outpout D2.DO for an analog input Vin= 3.349 V Select one: O a. D2.D0 = 100 O b. D2.DO - 101 Oc. D2.D0= 011 O d. D2.D0 = 111 Oe. None of the mentioned.
The output of the folloung than Vpo-VT. crravit cannot go (Voo = 1V,VT=03 V,ignore the baby eftect). eftfect). out in a) why? (kink: Vgs LUz → Io=0) b) What is going to be the max autput voltages for the fellaung crcuits. (laputs ore rising from o to l) b-4) in. out 0→1 b.2 ) 031. out 0-1
G1 = 100, G2 = 1000 and H = 0.009 for two block diagrams as open loop and closed loop given in the figure. a. Find the output voltages when the input voltage is 10 mV. b. For both systems, when G1 and G2 are doubled due to temperature increase, what will be the output voltages even though the input remains at 10 mV? c. Interpret the above results using the system's sensitivity principle. G2 H
Q3) For the circuit shown in below, determine and sketch the output waveform for the give input signals: - Vini = 2 sin(at) Vinz = 1 volt 100 k Ohm 50 k Ohm V_out 50 k Ohm V int 100 k Ohm V_in2
d) Design (Find the values of the R₁, R2, and C₁) an astable multivibrator circuit to have an output waveform as shown below in the figure (tH = 375µs and t₁ = 125µs). (Assume C₁ = C₂ and R₁ # R₂) and determine the frequency of oscillation and the duty cycle. R1: R2 C1 Q Vcc 4 555 5 C2 10nF I 8 1 3L -OVO tH = 375.0us tL = 125.0us