1. Links AB and AC and AD have cross-sectional areas of 80 mm, 30 mm² and 80 mm², respectively. The modulus of elasticity of AB and AD is 70 GPa and that of AC is 210 GPa. Determine the force and stress in each link when a vertical force P of 5 kN is applied at joint A. Assume Hooke's law applies and neglect the weight of the links. B P=5 KN

1. Links AB and AC and AD have cross-sectional areas of 80 mm, 30 mm² and 80 mm², respectively. The modulus of elasticity of AB and AD is 70 GPa and that of AC is 210 GPa. Determine the force and stress in each link when a vertical force P of 5 kN is applied at joint A. Assume Hooke's law applies and neglect the weight of the links. B P=5 KN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
Two rods, A and B. of equal free length are elastic. Both hang vertically 0.6m apart and support a rigid bar horizontally. The bar remains horizontal when a vertical load of 60 KN is applied to the bar 0.2m from A. If the stress in A is 100 MPa, determine the stress in B and the cross-sectional areas of the two rods: Ea = 200 GPa, EB = 130 GPa.
The bar ABC is supported by a pin at A and a steel wire at B. Determine the magnitudeof force Pinlbif the elongation of the wire is 0.059 in. The cross-sectional area of the wire is 0.0039 inandthemodulus of elasticity of steel is 29001 ksi,X=3.86 ft, Y = 6.78 ft, and L = 5.6 ft. Express the final answer to four decimal places. ... B Y
The cylindrical bar composed of two parts (AB and BC) is fixed at ends A and C. The two parts are made of different materials with different cross-sections. An external load ? =28 kN is applied at point B. The cross-sectional area of AB and BC part is 0.9 cm2and 0.3 cm2, respectively. The modulus of elasticity of the AB and BC part is 40 GPa and 200 GPa, respectively. Determine the force reactions at ends A and C.
5. Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring at A has coordinates (0, 0). If a load P acts on the ring at A, the normal strain in AB becomes EAB = 0.02 in/in., and the normal strain in AC becomes EAC = 0.035 in/in. Determine the coordinate position of the ring due to the load. 60 5 in. 8 in. A P
3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end segments DA and CB. Find the stress on each segment due to the applied loads. E of steel is 200 GPa and E of brass is 101 GPa. 250mm 250mm 250mm 50mm 20mm 50mm 75KN 100KN brass steel brass D B C 75KN 100KN
A weight W = 905 lb is held up by two cables each with a diameter of 1.5 in. Determine the tension in each cable and the normal stress in each cable. 0 = 21° O = 37° B Image is not drawn to scale.
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20o Properties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2 L = 2.75 m
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20oProperties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2
2. A replacement disc consists of the tube Cwith larger diameter of 4 cm, the cylindrical core B with the diameter of 2 cm and two relatively rigid discs on both ends. The disc replacement placed between vertebrae is under compressive force of 400N. The corresponding moduli of elasticity are Ec=10MPA and EB=20MPa. Determine the stress in the tube A and the core B. F Rigid parts 1cm C 2om 4cm F (Answer: OB = 509.3KPA, oc = 254.6KPA) 254.6KРа) %3D
Rod BD is made of steel (E = 29 × 106 psi) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.02P. If the stress must not exceed 18 ksi and the maximum change in length of BD must not exceed 0.001 times the length of ABC, determine the smallest-diameter rod that can be used for member BD. Take P = 148 kips.The smallest-diameter rod that can be used for member BD is in.
The 981-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 339 mm2. Find the location x (in mm) of P that can be safely applied to the bar if the stresses in AC and BD are limited to 119 MPa and 52 MPa, respectively. Express your answer in two decimal places.