1. A single stage single acting air compressor delivers 14m³ of free air per minute from 1bar to 7 bars. The speed of air compressor is 310 rpm and compression and expansion follows PV1.35 = c. Clearance volume is 5% of the piston displacement. Find out diameter or the bore and stroke (d x L) of the compressor if L = 1.5d.

1. A single stage single acting air compressor delivers 14m³ of free air per minute from 1bar to 7 bars. The speed of air compressor is 310 rpm and compression and expansion follows PV1.35 = c. Clearance volume is 5% of the piston displacement. Find out diameter or the bore and stroke (d x L) of the compressor if L = 1.5d.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s ANswer in one decimal places
Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m'/sec. 3. Specific speed.
1. A 451 mm x 491 mm air compressor has a piston displacement of 0.9 m^3/s. Determine the operating speed of the compressor (rpm) Answer in whole number 2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s Answer in one decimal places 3. A single stage air compressor hadles 0.454 m^3/sec of atmospheric pressure, 27 deg. C air, and delivers it to a receiver at 652.75kPa. Compression is isothermal. Determine the work in kW 4. An air compressor is to compress 8.878 m^3/min from 98.881 kPa to 988.493 kPa. Assuming condition is ideal, and n=1.3 What will be the work in kW due to 2 staging Answer in whole number
i. A wind turbine has the following data: Downstream wind velocity = 9 m/s Upstream wind velocity =18 m/s Rotor Power output = 1 MW a. Compute the wind rotor efficiency. b. Calculate power in the wind and the length of the rotor blades ii. ComparethedifferenttypesBiogasplants?
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW find the following: fuel consumption m'f = kg/ sec the air consumption engine capacity.: the flow rate of air intake to cylinder the Volumetric efficiency
B) The air flow to a four cylinder four-stroke engine is 2.15 m³/min. During a test on the engine the following data were recorded: Bore 10.5cm; stroke 12.5cm; engine speed 1200 rpm, torque 150 N.m, fuel consumption 5.5 kg/hr, calorific value of fuel, 43124 kJ/kg, ambient temperature 1-The brake thermal efficiency. and pressure are 20°C and 1.03 barş. Calculate: 2-The brakes mean effective pressure. 3-The volumetric efficiency.
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) thepump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
2. The specific speed of a turbine is 85 rpm and running at 500 rpm. What is the maximum power, in HP, delivered by the generator if the head is 25 m and generator efficiency is 90 %. Copy the problem, then show Complete Solution/s (i.e. transformations, equivalent formula, etc).
Data measured during tests of centrifugal pump driven at 3000 rpm are Parameter Inlet, Section 1 Outlet, Section 2 Gage pressure, p (kPa) 90 Elevation above datum, z (m) 10 Average speed offlow,V (m/s) The flow rate is 15 m3 /hr and the torque applied to the pump shaft is 6.5 N.m. The pump efficiency is 75%, and the electric motor efficiency is 85%. Find the electric power required, and the gage pressure at outlet, section 2. Write the pump specific speed in terms of the flow coefficient and the head coefficient.
Vacumm You are designing a vacuum system with a desired equilibrium pressure of 10-7 torr. The turbomolecular pump you are using has a pumping speed of 400 L/s. What is the maximium surface area of the chamber that you can allow, assuming that the outgassing rate per square cm 10-9 torr L/s? Note : total outgassing rate G = ( outgassing rate per area ) * ( area )
35. Water enters a heated tube of 2 mm diameter at 30 C and leaves the tube at 60 C. Find the water mass flow for the average Reynolds number of 1000. [Ans.: 0.00564 kg/s].
1. A single acting reciprocating air compressor has a clearance volume of 8%. Air is received at 100kpaa and 30°c and discharged at 600kpaa. The compression and expansion are polytropic with n=1.28. The pressure drop at suction port is 5kpa and at discharge port is 10kpa. The volumetric is 0.48m/min when operating at 900rpm. Determine a) The cylinder dimension if L/D=1.15. b) The mass of air drawn in kg/hr. c) The compressor power.