1. A pressure transducer is used multiple times to measure the pressure in atank. It turns out that all the measured values are consistent (i.e., the valuesare very close), but they differ from the true value. This pressure transducer isBoth precise and accurateNeither precise nor accurateAccuratePrecise

Accuracy is how close the measurement to the true values. While precision is how consistent or how…

Answered: 1. A pressure transducer is used…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Give some examples of Other Pressure Measurement Devices?
Explain the concept of calibration. pressure calibrator, digital tachometer, defibrillator analyzer, multi-parameter patient simulator and ultrasonography phantom Explain the concepts in detail.
Describe the concepts of independent, dependent, and extraneous variables using the illustration of a pressure measurement system.
The instrument used for air flow measurement in cooling tower experiment is called animometer. Select one: O True False
PLEASE ANSWER THEM ALL FOR AN UPVOTE. THANK YOU. Given: Pi constant to be used: 3.14159 Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg Liquid sample: density = 4 ml; time of flow = 4.5 seconds Ans. the ff questions. •What is the pressure in MKS unit? •What is the pressure in CGS unit? •What is the viscosity of the liquid? • If the weight was given as 8.5 grams, what will be the density of the liquid? •What is the kinematic viscosity of the liquid? •What is the fluidity of the liquid?
1. Pressure transducers are commonly used to meas Multimeter signals usually in the range of 4 mA to 20 mA or 0 V-dc to 10 V-dc in response to applied pressure. The system whose schematic is shown in Fig. 1 can be used to calibrate pressure transducers. A rigid container is filled with pressurized air, and pressure is measured by the manometer attached. A valve is used to D regulate the pressure in the container. Both the pressure and the electric signal are measured Pressure transducer Valve Pressurized air, P simultaneously for various settings, and the results are tabulated in Table 1. Rigid container i. For the given set of measurements, -Manometer obtain the calibration curve in the form of P = al + b, where a and b are Mercury SG= 13.56 constants Figure I ii. Determine the values of the constants a and b III. calculate the pressure that corresponds to a signal of 10 mA and 20 mA.
1. Pressures up to 3000 bar are measured with a dead-weight gauge. The piston diameter is 4 mm. What is the approximate mass in kg of the weights required? 2. A gas is confined in a 0.47 m diameter cylinder by a piston, on which rests a weight. The mass of the piston and weight together is 150 kg. The local acceleration of gravity is 9.813 m's-2, and atmospheric pressure is 101.57 kPa. (a) What is the force in newtons exerted on the gas by the atmosphere, the piston, and the weight, assuming no friction between the piston and cylinder? (b) What is the pressure of the gas in kPa? (c) If the gas in the cylinder is heated, it expands, pushing the piston and weight upward. If the piston and weight are raised 0.83 m, what is the work done by the gas in kJ? What is the change in potential energy of the piston and weight? 3. Steam at 1400 kPa and 350°C [state 1] enters a turbine through a pipe that is 8 cm in diameter, at a mass flow rate of 0.1 kg: s-1. The exhaust from the turbine is…
Water is flowing through a pipe. A pitot-static gauge registers 3 in of mercury. What is the velocity of the water in the pipe in m/s?A. 2.85B. 4.33C. 3.86D. 5.72
Bubbler device, Photometric level sensor Discuss shortly one industrial application for each level measurement device.
In static fluid, variation of pressure is due to O Weight of the fluid Velocity of the fluid Density of the fluid O Viscosity of the fluid
A method of determining viscosity consists of measuring the time for a known volume of the liquid to flow through a capillary section under the influence of gravity. O a. Capillary viscometry O b. Ostwald viscometry O c. Couette viscometry O d. Cone plate viscometry TOSHIBA
Oil is transported from A to B along a pipe of constant diameter. The pipe is inclined at 50° to the horizontal and B is at the higher elevation. Considering the flow from A to B, which statement is correct? O The pressure head is decreasing and the velocity head is increasing. O The pressure head and velocity head are both decreasing. O The pressure head is decreasing and the velocity head is constant. O The pressure head and velocity head are both increasing. O The pressure head is increasing and the velocity head is decreasing.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS