1. A 9.0 m uniform beam is hinged to a vertical wall and held horizontally by a 5.0 m cable attached to the wall 4.0 m above the hinge, as shown below. Let the mass m of the beam be 10.00 kg. (a) FIND THE TENSION T IN THE CABLE. HINT: THE TORQUES THAT ADD TO ZERO ARE DUE TO THE TENSION AND THE DOWNWARD WEIGHT OF THE BEAM. THEN SOLVE FOR T. Remember. The magnitude of the weight is mg. Find the horizontal and vertical components of the force the hinge exerts on (b) the beam.

1. A 9.0 m uniform beam is hinged to a vertical wall and held horizontally by a 5.0 m cable attached to the wall 4.0 m above the hinge, as shown below. Let the mass m of the beam be 10.00 kg. (a) FIND THE TENSION T IN THE CABLE. HINT: THE TORQUES THAT ADD TO ZERO ARE DUE TO THE TENSION AND THE DOWNWARD WEIGHT OF THE BEAM. THEN SOLVE FOR T. Remember. The magnitude of the weight is mg. Find the horizontal and vertical components of the force the hinge exerts on (b) the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 4: The bar ABC of negligible weight is supported by a pin at A and a rope that runs around the small pulley at D and the 10-kg homogeneous disk. a. Determine the tension in the rope. b. Determine Ax and Ay. D 450 mm 240 mm B 10 kg -450 mm 1350 mm
A container of weight W is suspended from ring A. Cable BAC passes through the ring and is attached to fixed supports at B and C. Two forces P = Pi and Q = Qk are applied to the ring to maintain the container in the position shown. Knowing that W=270 lbf, determine: - (a) The magnitudes (not vectors) P and Q. (b) The vectors P and Q canonically (cartesian vector notation) Hint: The tension is the same in both portions of cable BAC. yI 16 in. Z B A 10 W 48 in. P 72 in. 13 in. X 24 in.
The beam is subjected to a load F = 400 Nand is supported by the rope and thesmooth surfaces at A and B.a. Draw the free-body diagram of thebeam.b. What are the magnitudes of thereactions at A and B?
300 mm 30° -P 30° A 300 mm B. The two wires are connected togetherat A. If the force P causes point A to be displaced horizontally 2 mm, determine the normal strain developed in each wire.
Solve the problem using Moment -Area Method Problem II. The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminum rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I = 50 x 10 mm¹ for the beam, Eal = 70 GPa, and A = 42 mm² for the rod. 5 m H B |--2--|- m -Aluminum -Steel 2 m с
A distributed loading of p = (800x ) Pa acts over the top surface of the beam shown . Determine the magnitude and location of the equivalent resultant force.
1. Find the magnitude of the force component along the tube.
Question1 The uniform rectangular plate of mass m is suspended by three cables. Determine the tension in each cable. 0.8 m 0.3 m 0.4 m 0.3 m R -0.8 m B 0.5 m-
3. The beam BE is used for hoisting machinery. It is anchored by two bolts at B, and at C it rest on a parapet wall. The essential details are given in the figure. Note that the bolts are threaded as shown in Detail 1 with d=0.620 in. at root of the threads. If this arrangement is used to lift equipment of 10 kN, determine the stress in the bolts BD and the bearing stress at C. Assume that the weight of the beam in negligible in comparison with the loads handled. A A B Timber nominal Section 20cm x 30cm Bolts diam. ¾" 28 cm D View A-A 1m C₂ 18 cm 20cm Building 2.5 m 111 P=10 kN Detail 1 D d F E 11 Distributed Force equivalent to F Threaded bolt
3. The beam BE is used for hoisting machinery. It is anchored by two bolts at B, and at C it rest on a parapet wall. The essential details are given in the figure. Note that the bolts are threaded as shown in Detail 1 with d=0.620 in. at root of the threads. If this arrangement is used to lift equipment of 10 kN, determine the stress in the bolts BD and the bearing stress at C. Assume that the weight of the beam in negligible in comparison with the loads handled. B Timber nominal Section 20cm x 30cm Bolts diam. %" 28 cm View A-A 1m C 18 cm 20cm 2.5 m Building 111 P=10 kN Detail 1 D d F E 111 Distributed Force equivalent to F Threaded bolt
Problem 1 An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A, as shown in figure. The strength properties of the wire and the shear pin at B are , = 350 MPa (wire), and t-300 MPa (pin at B). If the wire and pin are to be sized to provide a factor of safety of the wire F.S = 3.3 and a factor of safety of the pin F.S = 3.5. What are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)? D 90 mm 20° 100 mm View a-a of B P = 2 kN
A load of 6kN is supported as shown in the figure. The weight of the pulley is 2kN. Neglect the weight of the bars. Support A and B are hinge connections. Give the hinge resultant force at C