1- The bearings at A and B exert only y and z components of force on the shaft. If Sy 150 MPa for the selected ductile material, determine the factor of safety if the shaft diameter is 40 mm. Use the maximum distortion-energy theory of failure. Show the following procedures through the calculation steps (Free Body diagram (FBD), Reaction at A and D, Bending moment diagram, point of max. moment, Torque diagram, draw the element showing general stress (ox, Txy), the factor of safety using the MDE. 500 N 100 mm 150 mm 200 mm 150 mm -100 mm 500 N

1- The bearings at A and B exert only y and z components of force on the shaft. If Sy 150 MPa for the selected ductile material, determine the factor of safety if the shaft diameter is 40 mm. Use the maximum distortion-energy theory of failure. Show the following procedures through the calculation steps (Free Body diagram (FBD), Reaction at A and D, Bending moment diagram, point of max. moment, Torque diagram, draw the element showing general stress (ox, Txy), the factor of safety using the MDE. 500 N 100 mm 150 mm 200 mm 150 mm -100 mm 500 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.31P

See similar textbooks

Similar questions

The gear forces shown act in planes parallel to the yz plane. The force on 20 in gear A is 300 lbf. Consider the bearings at O and B to be simple supports. For a static analysis and a factor of safety of 3.5, use both the DET and 16 in the MSST to determine the minimum safe diameter of the shaft. 10 in Consider the material to have a yield strength of 60 ksi. Gear A Solution: 24-in D. Gear C 10-in D. 20°
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram
After recording the applied twisting moment and resulted angle, fill the following table MT (N.m) T. MPa (degree) (rad.) Now, the twisting moment-twisting angle and shear stress-shear strain curves can be plotted, then determine maximum shear stress, shear stress at proportional limit and modulus of rigidity. 4-6 Problem The following torsion test data were obtained for AA6061-T6 aluminum alloy has a round cross section with 30mm outer diameter, 0 inner diameter and 100 length. 0 32 130 Twisted angle (): 0 1 Torque (N.m): 286 347 487 5.5 591 786 910 1105 1163 1235 1222 3.5 6.5 7.5 9. 10.5 13.5 16.5 21.5 25.5 > Plot the torque-twisted angle curve and determine the proportional limit on it. Plot the shear stress-strain curve the determine the shearing strength and modulus of rigidity. Prof. Adnan N. Abood Asst. Lec. Zainah Waheed 25
The static shaft shown below is machined from aluminum 6082-T6. It is subjected to a static force of P=20 kN, T1=50 Nm, T2=50 Nm (Assume there is no buckling, Sut=240 Mpa, oy= 200 Mpa, E=70 Gpa). a) Find out the factor of safety using appropriate failure criteria. b) Determine the critical point(s) of the shaft -100 mm T2 d=20 mm P. T1
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength ( Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (S) is equal to 0.8Su and endurance Strength (Se) is equal to 0, 5Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S - N diagram
42. The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find the value of the critical speed. Shaft is steel. Ans. n = 1810 rpm. Design of Shafts Chap. 3 248 t. 50 30 1"dia 10" 10" Figure 3-52 Problem 41. 10 kg 10 kg C B 375 600 mm 375 Figure 3-53 Problem 42.
4) Compute the fatigue life of a rotating hub and shaft assembly, if at a critical point in the shaft, the state of stress is described by σxx,max = 1000 MPa, σxx,min=-800 MPa, Txy,max = 300 MPa, Txy,min = -100 MPa, and σyy = σzz = Txz = σyz = 0. Employ the maximum shear stress thory of failure together with modified Goodman criterion. Take σ₁ = 2400 MPa and the fatigue-strength reduction factor K=1. [Use fracture stress as 0.9 times the ultimate stress, endurance stress as (1/3) times K times the ultimate stress, N = 103 cycles and Ne=108 cycles]
The plate of the figure is subjected to a bending moment with irregular cycles, which are repeated. In the graphic one of this cycles is represented in terms of stress which appears in each section whose height is h. The piece is made of ductile steel. Determine the number of repetitions of the sequence which the piece can resist before the failure takes place due to fatigue considering a reliability of 95 %. Data: Sult = 1.000 MPa Syp 3D800 Mра thickness e = 4 mm H = 10 cm h = 5 cm r=1 cm ka = 0,72 kp = 0,95 S(MPa) M 400 h 300 200 100 W -100 -200
The shaft is made of A-36 steel. It has a diameter of 38 mm and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for A-36 steel is 75 GPa. (Figure 1) Part A Determine the angle of twist of gear C with respect to B. Express your answer using three significant figures. vec Figure 1 of 1> rad Submit Request Answer 90 N-m 0.6 m Provide Feedback Ne 90 N-m 0.75 m 0.9 m
Problem 2: Let FA=100 N and F= 208.33 N for the shaft below. The bearings D and B act as pin supports. The shaft is made of 2014 aluminum alloy with a yield strength of 276 MPa. The shaft has a diameter of 8 mm. Based on the maximum shear stress (MSS) theory, determine if the shaft is safe. Determine the corresponding safety factor. Y 45 mm 30 mm D. 20 mm FC 20° Gear 1 50-mm dia. Shaft FA 20° Gear 2 24-mm dia.
The specifications for a coil spring are known. Infinite fatigue life is required, using a safety factor of 1.3 applied to the maximum load only. The fatigue strength can be represented by a line between τmax= 600, τmin= 0 and τmax= τmin= 900 MPa.Assume both end plates are in contact with nearly a full turn of wireand that the end plate loads coincide with the spring axis.Determine a suitable combination of d, D, and N, if C = 8
4. A tube composed of a wrought aluminum alloy 6061-T6 is designed to transmit a torque in a control mechanism; however the compressive stress in the tube must not exceed 7000 psi to prevent the tube from buckling. The tube has an outside diameter of 1.25 in., a wall thickness of 0.065 in. and total length of 2.0 ft. Find the maximum torque which can be applied and the angle of twist over the length of the tube at the maximum torque.