1-63.M. The key in Figure 1-18 has the dimensions b= 10 min, h = 8 mm, and L= 22 min. Determine the shear stress in the key when 95 N-m of torque is transferred from the 35-mm-diameter shaft to the hub. Hub F₁ End view Shear plane Shear pl T=Torque D=Shaft diameter T=F(D/2) F₁-Force of shaft F₂-Force of hub onl Shear area-A, -bxL

1-63.M. The key in Figure 1-18 has the dimensions b= 10 min, h = 8 mm, and L= 22 min. Determine the shear stress in the key when 95 N-m of torque is transferred from the 35-mm-diameter shaft to the hub. Hub F₁ End view Shear plane Shear pl T=Torque D=Shaft diameter T=F(D/2) F₁-Force of shaft F₂-Force of hub onl Shear area-A, -bxL

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A S S Q2. The double pulleys are fastened together to form a rigid unit. If V₁ = 9 and VB = 3 compute the angular velocity of the double pulley and the velocity of the load L. Use vector method. Also draw velocity-vector diagram of either pulley. Explain each step. Any illogical step will not be accepted. Refer to the following figure. UB B 600 mm- 400 mm L 1114
The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys Band Care as shown. Take a = 1.4 m, b= 0.9 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 300 N. m 200 N. m 45 mm 44 mm 40 mm Im Determine the angle of twist between Band C. The angle of twist between Band Cis|
Q2: A rectangular key is used to connect a gear on a shaft of d=50 mm. The shaft transmitting power at a maximum shear stress. The shaft is made of AISI 1040 CD steel and the key is made of AISI 1020 CD steel. Design the dimensions of the key. Take F.S =3.
UF3 80mm 60mm Vaxi's Gomm 40mm i 0= Find the location of the Controid. Show all work. (2). I GO
1-61.M Figure P1-61 shows the shape of a slug to be punched from a sheet of aluminum 5.0 mm thick. Compute the shear stress in the aluminum if a punching force of 38.6 kN is applied. 43 mm 35 mm -8 mm
solve show all steps/solutions show fbd with all forces and moments/torques
80mm Y SK 60mm V 120 mm Gomm 40mm ->; Statics -2x Criven the shape above, Find The location of the Controid. Show all work.
The circular shaft shown (Figure 2) has dimensions D1 = 24 cm , L1 = 6 mm, D2 = 17.5 cm, and L2 = 4 mm with applied torques T1 = 100 kN⋅m and T2 = 40 kN⋅m. The shear modulus is G1 = 60 GPa. Point B is halfway between points A and C. a) Draw the torque diagram for the shaft, using the right-hand rule to determine the correct signs. b) For the given shaft, what is the angle of twist at the free end, point D?
Question 1: A race car is turning (cornering) on a flat road, as shown in Figure Q1-1. The speed of the car is 300 kph and the turning radius is 260 m. Having the car parameters as below, answer questions a) and b). ● . ● ● m = 890 (kg) (57% of the weight is on the rear axle); Air density = 1.225 (kg/m3); Equivalent aerodynamic lift coefficient for front axle= -0.915 (-); Aerodynamic frontal area= 1.11 (m²); Slip angle of the front tyres= +2.4 (°); Slip angle of rear tyres= +1.2 (°); The steering angle of wheels= -1.9 (°); The efficiency of the drivetrain from the engine to the contact patch of tyres is 100%. 8=-1.9°- ---R=260 m α = +2.4° αR = +1.2° Figure Q1-1 Motion of the vehicle and the angles a) Calculate the engine power delivered to tyres to overcome the total induced drag due to lateral force.
The circular shaft shown (Figure 2) has dimensions D1 = 24 cm , L1 = 6 m, D2 = 17.5 cm, and L2 = 4 m with applied torques T1 = 100 kN⋅m and T2 = 40 kN⋅m. The shear modulus is G1 = 60 GPa. Point B is halfway between points A and C. a) Draw the torque diagram for the shaft, using the right-hand rule to determine the correct signs. b) For the given shaft, what is the angle of twist at the free end, point D?
The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are rotated through 180°? Assume the radius of the bicycle wheel is 12.7 inches. The bicycle will travel approximately (Round to the nearest tenth.) in. C -1.95 in 4.21 in
The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F₁ = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf-in is being transmitted through the shaft between the points of application of the forces. 1 / in ] A in [lin -10 in- F₁ in F₂ -10 in- All fillets in R. 12in] 3 in The value of the notch sensitivity is The value of the fatigue stress concentration factor is in NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the value of the theoretical stress concentration factor for torsion, the notch sensitivity, and the fatigue stress concentration factor? (You must provide an answer before moving to the next part.) The value of the theoretical stress concentration factor for torsion is