. A beam is constructed from a reinforced 50mm x 200mm section of timber using two L120x80x12 steel angle sections. Considering that the effort allowable stress in wood is 10 MPa, and the allowable stress in steel is 110 MPa. Determine the maximum positive and negative moment that the beam can support

. A beam is constructed from a reinforced 50mm x 200mm section of timber using two L120x80x12 steel angle sections. Considering that the effort allowable stress in wood is 10 MPa, and the allowable stress in steel is 110 MPa. Determine the maximum positive and negative moment that the beam can support

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum flexural stress in the beam loaded as shown below
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
A triangular beam, having a base of 300 mm, and a height of 500 mm. If fc' = 25 MPa, and the subjected maximum moment is 15 kN-m. Considering Uncracked Analysis. What is the actual tensile stress? 1.80 MPa O 3.60 MPa None of the Choices O 2.06 MPa O 2.88 MPa O 2.40 MPa
A rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The magnitude of the Ultimate moment capacity is Blank 1kN.m.
The rectangular wood beam is loaded as shown in the figure. Determine the largest allowable magnitude of the load P if the working stresses are 10 MPa in bending and 1.2 MPa in shear. P 150mm 8 kN/m 2m 1m B C 250mm
The wood beam has a square cross section. Find the smallest allowable cross-sectional dimensions if the working stresses are 8 MPa in bending and 1.0 MPa in shear | 5 kN 2 kN • m A D В +1.0 m –1.0 m →|
P2 - A rectangular beam has a design moment of 40 kNm. The material has a 200 MPa yield strength. Create a section with a width-to-depth ratio of 0.5 using the elastic and plastic theories, respectively.
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4 m and have a web width of 250 mm, an effective depth of 400 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-ϕ32 mm bars in two rows. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the ultimate bending moment strength of the T-beam in kN·m. 701 778 711 640
A beam carrying an allowable actual moment of -38 KN- m is reinforced as shown. If the the concrete is normal weight and f'c = 25MPa and fy = 420MPa. Determine the following: a. The cracking moment of the beam. b. The transformed moment of Inertia. c. The actual tension steel stress. d. Check the stress if it is correct by force checks. mm www.009 4-020 О 140 mm 300 mm 170 mm * 170 mm: ww.08 ✓ 60 mm
A rectangular beam has a concrete strength of 24 MPa. The yield strength of the reinforcing bars is 300 MPa. Width of the beam = 350 mm. What is the ultimate moment capacity of the beam in kN-m?
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4 m and have a web width of 250 mm, an effective depth of 400 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-ϕ32 mm bars in two rows. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the ultimate bending moment strength of the T-beam in kN·m. A. 640 B. 701 C. 778 D. 711
2.6-22 A compression bar having a square cross section with sides b = 50 mm is subjected to load P. The bar is constructed from two pieces of wood that are connected by a glued joint along plane pq that is inclined at angle a = 35°. The allowable stress in the wood in compression is 11.5 MPa and in shear is 4.5 MPa. Also, the allowable stress in the glued joint in compression is 3.5 MPa and in shear is 1.25 MPa. Determine the maximum load P that can be applied to the bar.