Lab3a_ReportTemplate

(01) DC biasing of diode circuits. (Course: Electronic Devices and Circuit Theory) -Redraw the circuit, Assume diodes are off and Redraw, Apply KVL/KCL. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you

how to solve this

In FET, An outward-pointing arrow represents ___. Choose the correct answer below: a.N-type substrate                              b.intrinsic substrate                           c.P-type substrate d.extrinsic substrate

Calculate the value of Xc for the circuit. Please show work. I will give you a thumbs up.

Draw a freehand sketch of the model of the structure that will house electronic circuit

Theoretical and calculation answer

(01) DC Si Diode Circuit. (Course: Electronic Devices and Circuit Theory) -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.

I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards on top of the train. Broadcast communication (which involves radio frequency, not Wi-Fi) would help communicate about the train's lateness to five other wooden trains on the same track. Local communication would help communicate to the train station about the train's lateness. I would also need radio frequency Tx-Rx Modules for discharging and undergoing the signal, and repeaters just in case the signal loses power due to long-distance traveling. My wooden train should be automated. It should run at 4 inches per second, keep a minimum distance of 30 seconds away from the other wooden trains, and make a 17-second-long stop every 500 seconds. What's the procedure to connect the components? What's the Arduino code (C++) for this project?

Summarize on how testing is carried out on isolators and circuit breakers of high voltage system. High voltage engineering

(02) Zener Diode Circuits. (Course: Electronic Devices and Circuit Theory) -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.

What is a Semiconductor? Explain the properties of a Semiconductor such as its physics, etc?     you better explain a little longer and illustrated pls

If you can, I need a sample answer with clear details because I want to understand the answer very well. This question from measurements instrumentation course. Thank you ❣❣ and good luck in your life.

Hand written plz asap please fast.... I'll give you multiple upvote hand written plz asap

Can you draw the circuit for this ? Thank you ?

ed Mar 17 ELEC 110 90-Degree Bends Worksheet copy Home Insert Draw Layout Review View ramond 14 A.. A E E E E A ELEC TIO 90° Bends Worksheet Overview Follow the directions to fill-in the missing values in the tables below. Assignment Determine the take-up and measurement to your mark for each of the following. Length EMT Size Take-up Stub-up Height Mark 70" 1/" 1' – 3" 70" 1" 2' – 0" 70" 16" 70" 1'/," 3' – 2" 70" 1' – 10" Determine the missing values for each of the back-to-back bends below. S2 Gain 71" 10" 15"

PS. This is Digital Electronics Subject

Pls help me answer number 3 NOTE: PLEASE ALWAYS USE 3 DECIMAL PLACES THROUGHOUT THE PROCESS. The other picture is the guide-sample. Thank you

Test the accuracy of the equation by applying the operation in Ampere law (del.)? If there is a mistake, correct this mistake.

1. What drawing instrument is used to mark or measure angles between 0 and 180˚? A. compass B. T-square C. protractor D. set squares   2. Who requires the knowledge of each schematic symbol assigned to an electronic component? A. Customer B. Electrician C. Technician D. Technologist   3. Why is it important to use drawing instruments when drafting electronic diagrams? A. To measure the components. B. To create a beautiful drawing. C. To be accurate with the drawing. D. To produce presentable drawings.

I have an O Gauge track and would like to convert it into a “sensored” track. Additionally, I would like to connect that track to an ESP-WROOM-32 board that should flash an LED whenever the track detects a non-moving train. Please list all the components (and how many of each) needed. Also, what’s the procedure for connecting the components?

Can you show this work written out and not typed, please and thank you!

Convert the HEX NUMBER B3F3. D75D to octal number showing the steps (Note : The problem should be solved in separate paper with steps and scanned copy should be submitted along with other answers Final answer can be entered in the boxes provided below. Enter only one digit in each box. ) Integer part = Fractional part =

Identify the following elements from the given block diagram.a)Measurement Elementb)Process Element c)Final Control Element  d)Control Law and Implementation element.